GE NetworX NX-4V2 Installation And Startup page 20

46 AUXILIARY OUTPUT 1 - 2 SPECIAL TIMING
Location 46 contains special timing feature activation for the four auxiliary outputs. Segment 1 corresponds to output 1; Segment 2
corresponds to output 2.
Segments 1 - 2:
1 = On if output should be timed in minutes; Off if timed in seconds.
2 = On if output should latch; Off if output should be timed.
3 = On if output should stop timing upon code entry; Off if the output should continue to time upon code entry.
4 = On if output should only activate between the closing and opening time in loc. 52 and 53.
5 = On if output should only activate between the opening and closing time in loc. 52 and 53.
6 = On if output should be inverted (0 volts going to 12 volts when activated).
7 = Reserved.
8 = Reserved.
47 AUXILIARY OUTPUT 1, EVENT & TIME
Segment 1: Use Table XIII-1 to select the event that will activate Auxiliary Output 1.
Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in Segment 1, Location 46).
Programming a "0" makes the output follow the event.
48 AUXILIARY OUTPUT 2, EVENT & TIME
Segment 1: Use Table XIII-1 to select the event that will activate Auxiliary Output 2.
Segment 2: Program the timing from 0-255 (minutes or seconds, depending on data programmed in Segment 2, Location 46).
Programming a "0" makes the output follow the event.
49 - 50 RESERVED
Table XIII-1 AUXILIARY OUTPUT EVENT SELECTION
DATA EVENT
0 /
Burglary Alarm
1  /
Fire Alarm
2  /
24 Hour Alarm
3  /
Trouble Alarm
4  /
Tamper Alarm
5 Yelping Siren (Burglary)
6 Temporal Siren (Fire)
7 Any Siren
8 Any Bypass
9 AC Fail
10 Low Battery
11  /
Duress
12  /
Aux 1 Keypad Zone
13  /
Aux 2 Keypad Zone
14  /
Panic Keypad Zone
15 Keypad Tamper
16  /
Autotest
17 Alarm Memory
18 Entry
˜
Events 49 & 50 require one or more of the following to operate: NX-408E, NX-416E, NX-448E wireless receivers, or NX-1700E card reader
/
If set to follow condition, these events will be 1 second.
Note:
When Event 48 is programmed, it is possible to program a user code's authorization to select which output(s) a particular code will activate.
When LED 8 is on for an authorization, then LEDs 1- 2 correspond to that code activating outputs 1 - 2 respectively. (See programming the
LED keypads on page 7.)
L
51 AUTOTEST CONTROL
Program a "1" if the interval is to be in hours; Program a "0" if in days. Add a A2" to suppress the daily test or a A3" to
Segment 1:
suppress the hourly test if any report has been sent.
Segment 2: Program the Autotest interval from 1-255 hours/days.
Segment 3: Program the Autotest report hour in 24-hour format (if the interval is in hours, this segment is ignored).
Segment 4: Program the Autotest report time, number of minutes after the hour.
20
SLOW COMMUNICATOR FORMAT CODES
DATA EVENT
19 Exit
20 Entry or Exit
21 Armed State
22 Disarmed State
23 Ready
24 Not Ready
25 Fire
26 Fire Trouble
27 Chime
28  /
Expander Trouble
29 Dynamic Battery Test Time
30 Open Period
31 Closed Period
32 Listen-In
33 Line Seizure
34 Ground Start
35 Fail To Communicate
36 Telephone Line Fault
37 Program Mode
WWW.DIYALARMFORUM.COM
2 ............ feature select
2 ............ numerical
2 ............ numerical
DATA
38 Download In Process
39 Smoke Power
40 Short Circuit (Over-current)
41 Box Tamper
42 Siren Tamper
43 Any Open
44 Any Short
45 Any Fault (Open/ Short on Non-Fire Zone)
46  /
Any Alarm
47 Beeping Keypad
48  /
Code Entry (See note below)
49 ˜ / Key FOB Function 1
50 ˜ / Key FOB Function 2
51 Always ON
52 Alarm Flash
53 Armed Away
54 Armed Stay
55 Aux Comm Fail
56 (CP-01) Progress Annunciation
4 ............ numerical
EVENT
NX-4V2 Control