Canon iR2000 Series Installation Procedures Manual
Installation card reader
Hide thumbs
Also See for iR2000 Series:
- Portable manual (34 pages) ,
- Service manual (738 pages) ,
- Reference manual (194 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Canon iR2000 Series
Summary of Contents for Canon iR2000 Series
- Page 1 Installation Procedure iR2000 Series Aug 23 2004...
- Page 3 When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
- Page 4 Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
- Page 5 Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the direction of the electric signal.
-
Page 7: Table Of Contents
Contents Contents 第 1 章 Installation Procedure 1.1 Installing the Card Reader ............................. 2 1.1.1Points to Note ..............................2 1.1.2Checking the Contents............................. 2 1.1.3Installation Procedure............................3 1.1.4Installation in a NetSpot Accountant (NSA) Environment ................7... - Page 8 Contents...
- Page 9 Chapter 1 Installation Procedure...
-
Page 10: 1.1 Installing The Card Reader
Chapter 1 1.1 Installing the Card Reader 1.1.1 Points to Note 0007-2705 The card reader must be used in combination with the Card Reader Mounting Kit-B1. 1.1.2 Checking the Contents 0007-2707 <Card Reader-C1> T-1-1 Card Reader-C1 1 pc. RS tightening screw (M4x10) 1 pc. -
Page 11: 3Installation Procedure
Chapter 1 T-1-2 Card reader base 1 pc. Relay harness 1 pc. TP screw (M4x25) 1 pc. TP screw (M4x8) 1 pc. Toothed washer 2 pc. F-1-2 1.1.3 Installation Procedure 0007-2709 When you have installed the Card Reader-C1, make the following selections, COPIER> FUNCTION> INSTALL> CARD, and enter the card number you will be using;... - Page 12 Chapter 1 F-1-3 1) Open the pedestal right door [1]. (if equipped with a Cassette Feeding Unit-Y2) 2) Open the lower right cover [2]. 3) Remove the 5 screws [3], and detach the right cover (rear) [4]. F-1-4 4) Remove the face plate [2] from the right cover (rear) [1] using nippers.
- Page 13 Chapter 1 F-1-5 5) Connect the relay cable [1] to the connector of the host machine F-1-6 6) Mount the rear right cover using 4 screws. 7) Mount the card reader [1] and the card reader base [2] using the included TP screw (M4x8) [4]. Be sure to use the washer [3] when doing so.
- Page 14 Chapter 1 F-1-8 9) Connect the cable [1] of the machine and the relay cable [2] of the card reader. F-1-9 10) While making sure that the harness swill not be trapped, mount the card reader [1] using a TP screw (4x25) [3] fitted with a washer [2].
-
Page 15: 4Installation In A Netspot Accountant (Nsa) Environment
Chapter 1 enter the appropriate card number (1 to 2001). -Use the number that is the lowest of all the numbers that the user will be using. -As many as 1000 cards may be used starting with the number entered. 13) Turn off the control panel power switch. - Page 17 Aug 23 2004...