Safety Rules - Hilti TE2 Operating Instructions Manual

02_BA_TE2_S_M_P1_en.qxd

Safety rules

1. General safety rules
-WARNING- Read all instructions! Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all of
the warnings listed below refers to your mains operat-
ed (corded) power tool or battery operated (cordless)
en
power tool.
SAVE THESE INSTRUCTIONS
1.1 Work area
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
1.2 Electrical safety
a) Power tool plugs must match the outlet. Never mod-
ify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of elec-
tric shock.
b) Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
1.3 Personal safety
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal
injuries.
c) Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
14
31.08.2007 10:39 Uhr
d) Remove any adjusting key or wrench before turn-
e) Do not overreach. Keep proper footing and balance
f) Dress properly. Do not wear loose clothing or jew-
g) If devices are provided for the connection of dust
1.4 Power tool use and care
a) Do not force the power tool. Use the correct power
b) Do not use the power tool if the switch does not turn
c) Disconnect the plug from the power source before
d) Store idle power tools out of the reach of children
e) Maintain power tools. Check for misalignment or
f) Keep cutting tools sharp and clean. Properly main-
g) Use the power tool, accessories and tool bits etc.,
1.5 Service
a) Have your power tool serviced by a qualified repair
Seite 14
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
ing the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in per-
sonal injury.
at all times. This enables better control of the pow-
er tool in unexpected situations.
ellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
extraction and collection facilities, ensure these
are connected and properly used. Use of these devices
can reduce dust related hazards.
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
making any adjustments, changing accessories, or
storing power tools. Such preventive safety mea-
sures reduce the risk of starting the power tool acci-
dentally.
and do not allow persons unfamiliar with the pow-
er tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's oper-
ation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
person using only identical replacement parts. This
will ensure that the safety of the power tool is main-
tained.