Table of Contents
Advertisement
Basic Connection
Antenna or Cable
Coaxial cable
Flat feeder
AC outlet
AC power cord
VHF/UHF IN (DVD/VCR)
COMPONENT VIDEO
OUTPUT
1
Back of unit
S-Video cable
Component
video cable
(not supplied)
To 75 ohm
terminal
It's essential that your unit be properly connected.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1
Make sure the package contains all of the accessories listed in
"SPECIFICATIONS" on page 87.
2
Place the unit on a stable, horizontal surface.
3
Connect the unit to a TV depending on the TV and cables you
use.
8 RF Connection
To connect to a TV with NO AV input connectors —
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the VHF/UHF IN (DVD/VCR)
connectors on the rear panel of the unit via antenna splitter.
C Connect the supplied RF cable between the TV OUT connector
on the rear panel of the unit and the TV's antenna terminal.
If you use the TV which has BNC connector, connect to a TV via the
supplied BNC/RCA (OUT) adapter.
NOTES:
Antenna splitter is not supplied. Purchase an optional antenna
splitter.
Two BNC/RCA adapters (IN and OUT) are provided with this unit.
Use the IN adapter for an input connector and the OUT adapter for an
output connector.
Matching transformer
(not supplied)
RF cable (not supplied)
Antenna splitter
(not supplied)
RF cable (not supplied)
AUDIO/VIDEO
OUTPUT
S-VIDEO
TV OUT
OUTPUT
Audio/video
cable
(supplied)
(supplied)
TV
RF cable
(supplied)
INSTALLING YOUR NEW UNIT
If you do not use antenna splitter, connect the TV antenna cable to
VHF/UHF IN (DVD) connector. However, it is not possible to record
the TV program on the VCR deck.
Connect the unit's ANT. LOOP OUT connector to the antenna input
connector on another vide unit.
8 AV Connection
To connect to a TV with AV input connectors —
A Perform A – B in "RF Connection".
B Connect the supplied audio/video cable between the AUDIO/
VIDEO OUTPUT connectors on the rear panel of the unit and the
TV's audio/video input connectors.
8 S-Video Connection
To connect to TV's S-VIDEO input and AUDIO input
connectors
A Perform A – B in "RF Connection".
B Connect the unit's S-VIDEO OUTPUT connector to the TV's
S-VIDEO input connector.
C Connect the unit's AUDIO OUTPUT connectors to the TV's
AUDIO input connectors.
You can obtain high-quality S-VHS pictures.
If your TV is not stereo-capable, use the unit's AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
8 Component Video Connection (DVD deck only)
To connect to TV's component video input connectors
A Perform A – B in "RF Connection".
B Connect the unit's COMPONENT VIDEO OUT connectors to
the TV's component video input connectors.
C Connect the unit's AUDIO OUTPUT connectors to the TV's
AUDIO input connectors.
You can obtain high-quality component video pictures.
If your TV is not stereo-capable, use the unit's AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to "Scan Mode Set" (
pg. 80).
4
Plug the end of the AC power cord into an AC outlet. This unit
performs Plug & Play Set automatically. (
The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first connected
to an AC outlet. (If "AUTO" and the channel indicator are displayed on
the front display panel before the unit is powered on, the clock and
tuner channels are being set automatically. Wait for the time to be
displayed on the front display panel before turning on the unit.)
"LOADING" blinks on the front display panel when the AC plug of the
power cord is connected into a mains outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
5
Set the video channel. The video channel is the channel on
which you can watch the picture from the unit on the TV when only
using RF connection.
With RF Connection
Set the video channel to "3 CH" or "4 CH". To set the video
channel, perform steps A – C below:
The video channel is preset to "3 CH". Set to "4 CH" if the Channel 3
is used for broadcasting in your area.
With AV or S-Video Connection
Set the video channel to "– CH" (off). To set the video channel,
perform steps A – C below:
With Component Video Connection (DVD deck only)
Set the video channel to "– CH" (off). To set the video channel,
perform steps A – C below:
How To Set The Video Channel
A Make sure that there is no cassette in the unit.
B Press 1 to turn off the unit, then press 8 on the unit for more
than 5 seconds. "3 CH" appears on the front display panel.
C Press CH +/– on the remote control to select "3 CH", "4 CH" or
"– CH" (off), then press ENTER. When either "3 CH" or "4 CH" is
selected, the TV/VCR indicator lights up.
17
EN
pg. 18)
Hide quick links:
Advertisement
Table of Contents
