Table of Contents
Advertisement
Setting the delay time
When playing in multi-channel mode and the speakers cannot all
be located an equal distandce from the listener, this setting can
compensate for the difference between the distance from the
front speakers (left, right) to the listener, and the distance from
the center speaker and the surround speakers to the listener.
Check the difference in the distance between the listener and the
front speakers (left, right), and the distance between the listener
and the other speakers, and then set that value as described in
the procedure below.
1
Bring up the SPK.SETTING menu.
2
Press 5/∞ to move
ENTER.
The [DELAY] display page appears on the TV screen.
DELAY
CENTER SPEAKER
0.0m/0ft
SURROUND SPEAKER
1.5m/5ft
RETURN
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER
TO EXIT, PRESS CHOICE.
3
Press 5/∞ to select the speaker to be set and
press ENTER.
CENTER SPEAKER: center speaker
SURROUND SPEAKER: surround speakers
4
Press 5/∞ to select the appropriate distance
and press ENTER.
When you select [CENTER SPEAKER], you can select the
appropriate distance from [0.0m] to [1.5m] in 30 cm (1 ft)
units.
When you select [SURROUND SPEAKER], you can select
the appropriate distance from [0.0m] to [4.5m] in 30 cm (1 ft)
units.
5
Repeat steps 3 and 4 if you want to set other
speakers.
To return to the [SPK.SETTING] page
5/∞
Press
to move
to [RETURN] and press ENTER.
Hint
If there is no difference between the distance from the front
speakers to the listener, and the distance from the center speaker
and/or the surround speakers to the listener, select [0.0m].
If there is a difference between them, refer to the following
diagram to set the delay time correctly.
Subwoofer
Center speaker
Front speaker
(L)
Surround speaker (L)
In the above example, set [CENTER SPEAKER] to [0.3m], and
[SURROUND SPEAKER] to [0.9m].
to [DELAY] and press
Front speaker
(R)
3.0m
2.7m
2.4m
2.1m
Surround speaker (R)
Changing the initial settings
As the distance from the center speaker and/or the surround
speakers to the listener is shorter than the distance from the front
speakers to the listener, select the longer distance value.
NOTE
This setting can only compensate for differences in speaker
distance when the front speakers (left, right) are farther from the
listener than the other speakers.
Setting the speaker level
You can adjust the output level of each speaker.
1
Bring up the SPK.SETTING menu.
2
Press 5/∞ to move
ENTER.
The [LEVEL] display page appears on the TV screen.
LEVEL
FRONT SPEAKER
0dB
CENTER SPEAKER
0dB
SURROUND SPEAKER
0dB
SUB WOOFER
0dB
TEST TONE
OFF
RETURN
SELECT
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXIT, PRESS CHOICE.
ENTER
3
Press 5/∞ to select the speaker to be set and
press ENTER.
FRONT SPEAKER: front speakers (This item cannot be
selected. The level is fixed to 0 dB.)
CENTER SPEAKER: center speaker
SURROUND SPEAKER: surround speakers
SUB WOOFER: subwoofer
4
Press 5/∞ to set the level and press ENTER.
The selectable level ranges from –6 to 6 dB in 1 dB unit.
5
Repeat steps 3 and 4 if you want to set other
speakers.
To return to the [SPK.SETTING] page
5/∞
Press
to move
to [RETURN] and press ENTER.
NOTE
For the speaker(s) whose size is set to [NONE], the speaker level
cannot be set.
To generate test tone signals
You can check the level setting by monitoring the test tone.
1
Press 5/∞ to select [TEST TONE] and press
ENTER.
2
Press 5/∞ to select [ON] and press ENTER.
The test tone will be generated when you select the
speaker(s) in the [LEVEL] page.
NOTE
The test tone sound is not output from the subwoofer.
to [LEVEL] and press
41
Advertisement
Table of Contents
