Table of Contents
Advertisement
Quick Links
n Lifetime Warranty
n His & Hers Remote Controls
n ACG™ 2 (Anti-CodeGrabbing™)
n Extended Range Receiver
n Audible Low-Battery Warning
n Built-In Two-Point Immobilizer™
n Optional Wireless Immobilizer™
n Patented UltraSecure Coded Valet Mode™
n Remotely Adjustable Dual-Zone Piezo Sensor
n FACT — False Alarm Control and Test
n Enhanced User-Selectable AutoArming
n User-Selectable Remote Valet Mode Entry/Exit
n Built-In BlackJax Anti-Carjacking System
n Optional DataPort™ Interface and CliffNet Wizard™
Software
n Remote Panic with Smart Locking/Unlocking
n Remote Door Locking/Unlocking
n User-Selectable AutoLock
n Remote Keyless Entry and Accessory Activation Even in
Valet Mode
n Integrated Electronic Timer
n Turbo Timer Output
n DataPort Accessory Interface
n Prewired LED, Sensor, Extended Range Receiver and
PlainView 2 Switch Connectors
The IntelliGuard 7000 kit contains the following components:
One Prewired 24-pin Connector Harness
One Prewired 4-pin Connector Harness
One IntelliGuard 7000 Control Unit
One Remotely Adjustable Dual-Zone Piezo Sensor
One Medallion Siren
One PlainView 2 Coded Valet Switch
In tel liGuard 7000/199
Standard Features of the IntelliGuard 7000
System Components
n High-Output Medallion Siren
n Eight-Event TotalRecall™
n Dual-Mode "Chirp" Silencing
n Remote Siren Silencing
n Smart Remote Trunk Release
n Built-In Dual Parking Light Flasher with Onboard Relay
n Remote-Controlled Courtesy Lighting
n Patented Smart AutoTesting™
n Patented Malfunction AutoBypass™ with
AutoReMonitoring
n Patented Smart Prior Intrusion Attempt Alert
n Patented Remote Control Code Learning and MultiRemote
Recognition
n Clear All Remotes
n Multiple-Car Control
n High-Luminescence LED Status Indicator with Automatic
Battery-Saving Mode
n Multiple Sensor/Trigger Inputs
n Patented SmartPowerUp™ 2
n Advanced CMOS Microcomputer
n Three Accessory Channels with Selectable Output Types
n Pre-Loomed Wiring
n Full-Time SecureAccess™ Programming
n AutoActivation of Auxilliary C Output for Window
All-Close
n Installer-Selectable Door Ajar/Delayed Courtesy Lights
One Extended Range Receiver
One LED Status Indicator
One Owner's Manual
One Hardware Kit
Two Window Decals
Two Remote Transmitters
1
Advertisement
Table of Contents
Related Manuals for Directed Electronics IntelliGuard 7000
Summary of Contents for Directed Electronics IntelliGuard 7000
-
Page 1: System Components
Prewired LED, Sensor, Extended Range Receiver and All-Close PlainView 2 Switch Connectors n Installer-Selectable Door Ajar/Delayed Courtesy Lights System Components The IntelliGuard 7000 kit contains the following components: One Prewired 24-pin Connector Harness One Extended Range Receiver One Prewired 4-pin Connector Harness One LED Status Indicator One IntelliGuard 7000 Control Unit One Owner’s Manual... - Page 2 Wiring Description for the 24-Pin Connector Pin col our Con nects to Violet LED output (+) Black/Gray Ignition coil or tach input Green Armed output (Accessories) (-) Orange Optional sensor input trigger zone (-) Gray/Yellow Trunk trigger switch input (-) Gray/Orange Door unlock output (+ or -) White/Black...
- Page 3 In tel liGuard 7000/199...
-
Page 4: Passenger Compartment Connections
Control Unit and Extended Range Receiver The IntelliGuard 7000 con trol unit must be in stalled in side the ve hi cle. Un der no cir cum stances should the unit be in stalled un der the hood or other simi larly hos tile en vi ron ment. -
Page 5: Engine Bay Connections
Passenger Compartment Connections (Continued) Starter and Ignition Immobilization Circuits 1. Locate the ignition switch wireloom under the dash and use a voltmeter to locate the one wire that carries +12V throughout BOTH the cranking AND engine running cycles, and 0 volts when the ignition is off. 2. -
Page 6: Final Wiring Connections
The IntelliGuard 7000 comes with two ergonomically designed remote controls. Up to two more ACG 2 remote controls can be added to the IntelliGuard 7000 system. Due to the ACG 2 feature on the IntelliGuard Series systems, older Clifford ACG and non-ACG remotes are not compatible with the IntelliGuard 7000. -
Page 7: Remote Control Channel Assignments
Remote Control Operation (Continued) NOTE: One sec ond af ter you stop trans mit ting levels 2, 3 or 4 (chan nels 5–16), the re mote con trol auto mati cally re turns to level 1 (chan nels 1–4). Remote Control Channel Assignments Chan nel # Func tion Chan nel #... -
Page 8: Sensor Adjustment
1 again to fully exit Piezo Sensor adjustment mode (you will hear 3 chirps). 4. Repeat the preceding steps as required. An improperly adjusted sensor will cause the IntelliGuard 7000 to false alarm or not respond properly to a genuine threat. -
Page 9: Programmable Features
Programmable Features IntelliGuard 7000 comes from the factory with its features preprogrammed as noted in bold text in the tables on pages 10 and 11. Some features can be programmed by the installer or the user, others can only be programmed only by the installer. -
Page 10: User-Programmable Features
When you hear two chirps, all remote controls will have been erased from the system memory. You must now add NOTE 3: the new and/or existing remote controls to the system (i.e., AutoProgram each remote that will be used with the IntelliGuard 7000). Programs a 4-channel secondary, 16-channel master, or any other remote control from another IntelliGuard NOTE 4: system to arm or disarm the vehicle. -
Page 11: Installer-Programmable Features
System Checklist & Troubleshooting The fol low ing check list and trou ble shoot ing tips will as sure that you have in stalled the IntelliGuard 7000 cor rectly. If the sys tem does not re act as noted, fol low the trou ble shoot ing tip(s) de noted with a black box be low that item, then re peat the step. Each suc ces sive step re quires that the pre vious step has been com pleted as in di cated. - Page 12 Step 2. Test the Im mo bi li za tion cir cuits. Arm the IntelliGuard 7000 (either from inside or outside the vehicle) and wait 10 seconds. Turn the ignition to the “ON” position. Engine does not respond. This is the correct response, proceed to the immobilization test.
- Page 13 No flashes. If the LED does not flash, ver ify that the LEDs VIO LET and BLACK wires are sol idly con nected to the same colour wires on the IntelliGuard 7000’s wire loom. Warn ing: This is a 2- volt LED, test ing with 12 volts will de stroy the LED.
- Page 14 1 of this sec tion. Check the IntelliGuard 7000’s 10- amp fuse. If the fuse blew when you dis armed, the ve hi cle uses a posi tive door trig ger and you con nected the in te rior light sup ply wire to ground in stead of +12 volts. Re place the 10-amp fuse and retest.
- Page 15 Stand approximately 50 feet from the vehicle and use the remote control to arm and disarm the system. The IntelliGuard 7000 will re spond with the pre vi ously noted in di ca tions for arm ing and dis arm ing. If not: Re po si tion the external receiver as high as possible high up un der the dash, or as high as possible along side the windshield pillar and as far as pos si ble from heavy wire looms and metal.