Selecting The Fan Speed - Carrier 40 GKX Owner's Manual

40 GKX
Use of the remote control (if applicable)
Combined programming
The combined program (a selection of a sequence of start and
stop times) will start and stop the air conditioner each day at the
programmed times, without the need of user intervention. To acti-
vate this function proceed as follows:
1. Repeatedly press button G
bol appears on the display; now set the desired start time, as
indicated in the "programmed start time" section.
2. Press button G again to show the symbol for the pro-
grammed stop time and set the desired stop time.
3. Press button G , until the symbol for the combined program
appears; together with this symbol, the symbols for the start
and stop programs appear alternatively along with the respec-
tive programmed times.
4. To confirm the program, press button C
the unit will illuminate.
5. If the programmed times for start and stop coincide, the com-
bined operation mode will not function.
The TIMER operation mode can be cancelled at any time by
pressing button C : indicator P
the indication of the timer mode will disappear from the display on
the remote control.
The unit will store the mode in which was operating at that time:
ON if it was in operation, ON if it was turned OFF.
When the timer mode is ON (unit indicator P
remote control will always display the symbol relevant to the
current timer program; the actual time will be displayed.
When a programmed start or stop has been selected, once the op-
eration has been carried out at the desired time, the unit will re-
main in the TIMER operating mode selected. To change the oper-
ating mode, it is necessary to manually start or stop the unit or se-
lect a new program by pressing button C
In the event of a power failure during timer mode operation, the
unit will restart (when power is restored) and return to the last op-
erating position before the power cut: unit indicator P
to show that the Timer mode is OFF. To reactivate the timer mode,
press button C twice.
Time adjustment
(buttons H and I)
To set the time for the timer programs selected with button G
press the buttons H and I
serve to adjust the time shown on the display in the CLOCK
section.

Selecting the fan speed

(button J)
The fan speed can be selected by pressing button J
Simbol on display
Low speed
(for night operation)
Medium speed
High speed
(to reach temperature)
Automatic
(Fan speed will automatically switch to the value required
for optimum comfort). When this function is activated, the
dotted symbols will flash.
GB - 8
until the programmed start sym-
. Indicator P
on the unit will turn OFF, and
illuminated) the
.
will flash
. Buttons H and I also
.
Night stop
(button K)
This function optimizes comfort at night, taking into account
variations in the human metabolism.
One hour after activation of this function, the temperature (set for
cooling) will increase by 1°C, or decrease by 1°C (if heating), up to
2°C in two hours. After 5 hours the unit will stop completely.
The system will automatically operate at low fan speed to minimize
sound level.
When activating this function, the remote control will show the time
when the air conditioner will completely stop.
Press button C to deactivate the function.
on
Positioning
the air outlet louvres
(button L)
In order to optimise air distribution in the room, the air flow direction
can be varied. By pressing button L
the louvres can be selected.
Simbol on display
Automatic
The air flow direction is controlled automatically. During
cooling the deflecting louvres will direct the air close to the
ceiling (Coanda effect); when heating, the air will be
directed towards the floor in order to prevent layers of hot
air forming in the upper part of the room.
Simbol on display
Swing
The louvres move continually from the bottom upwards in
,
order to supply better air distribution.
Adjusting clock time
(button M)
To adjust the clock time, put the remote control in the ON position
by pressing button B
To adjust the time shown in the CLOCK section, proceed as fol-
lows:
• Gently press the recessed button at the right corner of the
remote control battery compartment with a pointed instrument
(e.g. a pencil point): the hour figures will flash.
Use buttons H
time of day.
• Press the recessed button a second time and the minute figures
will flash. Adjust them to the correct value in the same way.
• Pressing the recessed button a third time will activate the clock
function.
in sequence, the position of
6 positions can be selected.
The louvres can be adjusted to provide
6 different air flow directions.
(after inserting the batteries).
and I to adjust their value to the correct