Napoleon BGNV42N Installation And Operation Instructions Manual
Natural and propane gas fireplace
Hide thumbs
Also See for BGNV42N:
- Installation and operation instructions manual (16 pages) ,
- Installation and operation instructions manual (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Napoleon BGNV42N
Summary of Contents for Napoleon BGNV42N
- Page 1 W415-0377 / E / 11.26.07 W415-0377 / E / 11.26.07 $10.00...
-
Page 2: Table Of Contents
TABLE of CONTENTS PG 2-4 INTRODUCTION PG 10 OPTIONAL BLOWER INSTALLATION Warranty 11 OPTIONAL FAN INSTALLATION General Instructions OPTIONAL THERMOSTATIC SENSOR General Information 12-13 OPERATION / MAINTENANCE Care of Glass & Plated Parts Operating Instructions 5 VENTING Maintenance Vent Safety Switch 13 ADJUSTMENTS Hi Limit Switch Venting Action Check... - Page 3 NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2000 Quality Assurance Certifi cate. NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The burner and valve assembly are leak and test-fi red at a quality test station. The complete fi...
-
Page 4: General Instructions
GENERAL INSTRUCTIONS CARE OF GLASS, AND PLATED PARTS THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED Do not use abrasive cleaners to clean plated parts. Buff lightly with BY A QUALIFIED INSTALLER to conform with local codes. Installa- a clean dry cloth. The fi replace is factory equipped with 3/16" thick tion practices vary from region to region and it is important to know tempered glass. -
Page 5: Venting
VENTING This is a vented appliance and must be connected to a chimney in VENTING ACTION CHECK accordance with the current installation codes. In absence of local codes, install to the current National Fuel Gas Code, ANSI Z223.1, A test for correct venting action must be made before the in- or the current CAN/CGA B149, Installation Codes. -
Page 6: Installation
INSTALLATION When roughing in the fi replace, raise the fi replace to accommodate GAS INSTALLATION for the thickness of the fi nished fl oor materials, i.e. tile, carpeting, Proceed once the vent installation is complete. hard wood, which if not planned for will interfere with the opening of the lower access door and the installation of many decorative NOTE: All gas connections must be contained within the fi... -
Page 7: Nailing Tab Installation
MINIMUM MANTEL AND NAILING TAB INSTALLATION ENCLOSURE CLEARANCES 1) Attach the nailing tabs to the corner posts using the 2 sheet metal screws supplied. Secure through Combustible materials may be installed fl ush with the front of the the centre of the top and bottom fi... -
Page 8: Finishing
FINISHING L42 LOUVRE INSTALLATION LOG PLACEMENT PHAZER logs and glowing embers, exclusive to Napoleon® Fire- FIGURE 17 places, provide a unique and realistic glowing effect that is different in every installation. Take the time to carefully position the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fi... -
Page 9: Optional Blower Installation
CHARCOAL EMBERS Randonly place the charcoal embers along the front and sides of the log support tray in a realistic manner. Fine dust found in the bottom of the bag should not be used. VERMICULITE Sprinkle vermiculite around the charcoal embers. Note: Both charcoal embers and vermiculite are not to be placed on the burner. -
Page 10: Optional Fan Installation
OPTIONAL FAN INSTALLATION ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED IN- Position the vibration reducing pad into the clip and STALLER and must be connected and grounded in accordance with onto the threaded stud at the other end, piercing local codes. -
Page 11: Maintenance
MAINTENANCE 3. Check to see that all burner ports are burning. Clean out any of Turn off the gas and electrical power before servicing the the ports which may not be burning or are not burning properly. fireplace. CAUTION: Label all wires prior to disconnection when servicing 4. -
Page 12: Replacements
REPLACEMENTS Contact your dealer or the factory for questions concerning prices 1. M & S ODEL ERIAL UMBER OF FIREPLACE and policies on replacement parts. Normally all parts can be ordered 2. I NSTALLATION DATE OF FIREPLACE through your Napoleon® dealer or distributor. 3. -
Page 13: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE EFORE ATTEMPTING TO TROUBLESHOOT PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR REMOVED SYMPTOM PROBLEM TEST SOLUTION Main burner goes out; Pilot fl ame is not large enough or - turn up pilot fl... - Page 14 SYMPTOM PROBLEM TEST SOLUTION Flames are consist- Unit is over-fi red or under-fi red. - check pressure readings: ently too large or too Inlet pressure can be checked by turning screw (A) counter-clockwise 2 or 3 small. Carboning oc- turns and then placing pressure gauge tubing over the test point. Gauge should curs.