Napoleon BGNV36N Installation And Operation Instructions Manual
Millivolt system vented natural and propane gas fireplace
Hide thumbs
Also See for BGNV36N:
- Installation and operation instructions manual (21 pages) ,
- Installation and operating instructions manual (32 pages)
Table of Contents
Advertisement
Quick Links
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.22, AND ANSI Z21.50 RESPECTIVELY FOR VENTED GAS FIREPLACES.
INSTALLATION AND OPERATION INSTRUCTIONS FOR
WARNING: If the information in these instructions is not followed exactly, a fire or explo-
sion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
Installation and service must be performed by a qualified installer, service agency or the
gas supplier.
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)722-6031
MILLIVOLT SYSTEM
VENTED GAS FIREPLACE
NATURAL GAS MODEL
PROPANE GAS MODEL
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / CSA METHODS
FOR YOUR SAFETY
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
www.napoleonfireplaces.com • ask@napoleon.on.ca
BGNV36N
BGNV36P
• Immediately call your gas supplier from a
neighbour's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call
the fire department.
1
W415-0275 /D / 10.01.07
Advertisement
Table of Contents
Related Manuals for Napoleon BGNV36N
Summary of Contents for Napoleon BGNV36N
-
Page 1: Millivolt System
Installation and service must be performed by a qualified installer, service agency or the gas supplier. Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)722-6031 www.napoleonfireplaces.com • ask@napoleon.on.ca W415-0275 /D / 10.01.07... - Page 2 T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS PG10 OPTIONAL BLOWER INSTALLATION PG 2-4 INTRODUCTION Warranty 11 OPTIONAL FAN INSTALLATION General Instructions OPTIONAL THERMOSTATIC SENSOR General Information Care of Glass & Plated Parts 12-13 OPERATION / MAINTENANCE Operating Instructions 5 VENTING...
- Page 3 ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® W415-0275 /D / 10.01.07...
-
Page 4: General Instructions
In absence of local codes, install the fireplace to the equipped with 3/16" thick tempered glass. Use only re- current National Fuel Gas Code, ANSI Z223.1, or the placement glass available from your Napoleon dealer. current CAN/CGA B149, Installation Codes. Do not substitute materials. -
Page 5: Safety Switch
VENTING This is a vented appliance and must be connected to a HIGH LIMIT SWITCH chimney in accordance with the current installation codes. In absence of local codes, install to the current This thermally activated switch, located in front of the draft National Fuel Gas Code, ANSI Z223.1, or the current hood, senses an increase in temperature and acts as a CAN/CGA B149, Installation Codes. -
Page 6: Gas Installation
GAS INSTALLATION FRAMING Proceed once the vent installation is complete. It is best to frame your fireplace after it is positioned and 1. Move the fireplace into position and secure using the the vent system is installed. Use 2x4's and frame to local nailing tabs and/or secure to the floor through the 1/4"ø... -
Page 7: Nailing Tab Installation
NAILING TAB INSTALLATION FIGURE 12 a-c 1) Attach the nailing tabs to the corner posts using CORNER the 2 sheet metal screws supplied. Se- POST cure through the centre of the top and FIGURE 11 bottom slots in the nailing tab and then NAILING through the existing holes in the cor- ner posts. -
Page 8: Door Opening & Closing
FINISHING L36 LOUVRE INSTALLATION DOOR OPENING & CLOSING The upper louvres must be FIGURE 17 FLANGE removed to allow the door CLIP to be opened or closed. To access the lower door latch, open the valve con- trol door. Release the top UPPER LOUVRE and bottom door latches, lo- cated at the right side of the... -
Page 9: Log Placement
LOG PLACEMENT PHAZER logs and glowing embers exclusive to Napoleon Fireplaces, provide a unique and realistic glowing effect that is different in every installation. Take the time to care- fully position the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. -
Page 10: Optional Blower Installation
OPTIONAL BLOWER INSTALLATION Attach the connectors from INSTALLATION TO BE DONE BY A QUALIFIED the black and white wires THERMODISC INSTALLER and must be to the thermodisc and se- electrically connected and cure thermodisc grounded in accordance bracket to the securing RECEPTACLE / with local codes. -
Page 11: Optional Fan Installation
GD65 Fan Kit, shown above, which may be or- curing stud located next to the receptacle/junction box at dered from your Wolf Steel / Napoleon dealer. the bottom left of the unit using the lock washer and wing nut. - Page 12 OPERATION / MAINTENANCE Purge all gas lines with the glass door of the fireplace After extended periods of non-operation such as fol- opened. Assure that a continuous gas flow is at the lowing a vacation or a warm weather season, the fire- burner before closing the door.
-
Page 13: Maintenance
The flow of combustion and ventilation air must on. A 5 to 10 second total light-up period is satisfactory. If not be obstructed. ignition takes longer, consult your Napoleon dealer / dis- tributor. 1. In order to properly clean the burner and pilot assembly, 7. -
Page 14: Replacement Parts
Contact your dealer or the factory for questions concerning When ordering replacement parts always give the follow- prices and policies on replacement parts. Normally all parts ing information: can be ordered through your Napoleon dealer or distributor. 1. M & S ODEL... - Page 15 W415-0275 /D / 10.01.07...
-
Page 16: Troubleshooting Guide
TROUBLE SHOOTING GUIDE EFORE ATTEMPTING TO TROUBLESHOOT PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR OPENED SYMPTOM PROBLEM TEST SOLUTION Main burner goes Pilot flame is not large - turn up pilot flame. out;... - Page 17 SYMPTOM PROBLEM TEST SOLUTION Pilot goes Gas piping is undersized. - turn on all gas appliances and see if pilot flame flutters, dimin- while standing; ishes or extinguishes, especially when main burner ignites. Monitor Main burner is in appliance supply working pressure. 'OFF' position.
- Page 18 W415-0275 / D / 10.01.07...
- Page 19 NOTES W415-0275 /D / 10.01.07...
- Page 20 NOTES W415-0275 / D / 10.01.07...