Lighting Instructions; Operating Instructions; To Turn Off Gas To Appliance; For Your Safety - Goodman GMP Installation & Operating Instructions Manual

These instructions are also on the furnace
FOR YOUR SAFETY READ BEFORE OPERATING
A. This appliance does not have a pilot. It
is equipped with an ignition device which
automatically lights the burners. Do not
try to light the burners by hand.
B. BEFORE OPERATING smell around
the appliance area for gas. Be sure to
smell next to the floor because some gas
is heavier than air and will settle on the
floor.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electric switch;
do not use any telephone in your
building.
Immediately call your supplier
from a neighbor's phone. Follow
the gas suppliers instructions.
1. STOP! Read the safety information
above on this label.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appl-
iance.
4. This appliance is equipped with an
automatic ignition system which autom-
atically lights the burners. Do not try to
light the burners by hand.
5. Remove control access panel.
6. Move the gas control switch or knob
to "OFF".
GAS CONTROL
SWITCH SHOWN
IN "ON" POSITION

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to its lowest setting.
2. Turn off all electric power to the
appliance if service is to be performed.
3. Remove control access panel.

FOR YOUR SAFETY

other flammable vapors and liquids in the vicinity of this
or any other appliance.
IO137

LIGHTING INSTRUCTIONS

If you do not follow these instructions exactly,
a fire or explosion may result causing property
damage, personal injury or loss of life.
C. Use only your hand to move the gas
control switch or knob. Never use
tools. If the gas control switch or knob
will not operate, don't try to repair it,
call a qualified service technician.
Force or attempted repair may result in
a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately call
a qualified service technician to inspect
the appliance and to replace any part of
the control system and any gas control
which has been under water.

OPERATING INSTRUCTIONS

7. Wait five (5) minutes to clear out any
gas. If you then smell gas, STOP!
Follow "B" in the safety information
above on this label. If you don't smell
gas, go to the next step.
8. Move the gas control switch or knob
to "ON".
9. Replace control access panel.
10. Turn on all electric power to the
appliance.
11. Set the thermostat to the desired
setting.
12. If the appliance will not operate,
follow the instructions "To Turn Off Gas
To Appliance" and call your service
technician or gas supplier.
GAS CONTROL
KNOB
4. Move the gas control switch or knob
to "OFF". Do not force.
5. Replace control access panel.
Do not store or use gasoline or
If you cannot reach your gas supplier,
call the fire department.
GAS CONTROL
SWITCH SHOWN
IN "ON" POSITION
27
WARNING: Improper
installation, adjustm-
ent, alteration, service
or maintenance can
cause injury or prop-
erty damage. Refer to
the user's information
manual provided with
this furnace. For ass-
istance or additional
information consult a
qualified installer, ser-
vice agency or the
gas supplier.
This furnace must be
installed in accordan-
ce with the manufac-
turers instructions
and local codes. In
the absence of local
codes follow the
National Fuel Gas
Code, ANSI Z223.1.
For indoor installation.
PGB & PGJ
For outdoor install-
ation only.
WARNING: If not ins-
talled, operated and
maintained in accord-
ance with the manuf-
acturer's instructions,
this product could
expose you to subst-
ances in fuel combus-
tion which can cause
death or serious illn-
ess and which are
known to the State of
California to cause
cancer, birth defects
or other reproductive
harm.
This product contains
fiberglass insulation.
Fiberglass insulation
contains a chemical
known by the State of
California to cause
cancer.
B14933-228