Channel Data Items; Dcs Typ: Dcs Format; Rev Bst: Reverse Burst.; Court Blip: Courtesy Blip - Vertex Standard VXR-7000 Service Manual

Operating Manual Reprint

Channel Data Items

Ch: Channel Number
This 2-digit number (01 - 16) is used to identify the chan-
nel. Channel numbers occur in sequence, and their order
can not be changed.
Rx Freq.: Edit Receive (or simplex) Frequency
Use the [0] - [9] keys to enter the desired channel fre-
quency directly, and press the [E
CTCSS Decoders: Toggle CTCSS Decoder ON/OFF,
sets CTCSS Frequency
Press the [S ] bar to toggle the CTCSS Decoder "on"
PACE
or "off," or press the [E
S " window, from which
ELECT
you may select a CTCSS fre-
quency using the [A
RROW
press [E ] again to accept the
NTER
selected tone, or press [E
SC
to cancel.
DCS Decoders: Toggle DCS Decoder ON/OFF, sets
DCS Code #
Press the [S ] bar to toggle the DCS Decoder ON or
PACE
-
OFF, or press the [E
N
] key to display the
TER
"C S " win-
ODE ELECT
dow, from which you
may select a DCS code
using the [A ] key;
RROW
press [E ] again to accept the selected code, or press
NTER
the [E ] key to cancel.
SC
W/N: Wide/Narrow Channel Spacing
This function selects the channel spacing environment in
which the VXR-7000 operates.
W (Wide) = 25 kHz Channel Spacing, ±5 kHz De-
viation.
N (Narrow) = 12.5 kHz Channel Spacing, ±2.5 kHz
Deviation.
Press the [S ] bar to select the desired channel spac-
PACE
ing environment.
Clk Sft: Enable/disable the CPU Clock Shift
This function is only used to move a spurious response
"birdie" should it fall on a current frequency.
Press the [S ] bar to toggle "yes" or "no."
PACE
10
] key.
NTER
] key to display the "T
NTER
] key;
] key
CE27 Main Screen (Scrolled Right)
NSQ Mode: Noise Squelch Mode
This command selects the manner of setting of the Squelch
threshold level.
User = The squelch threshold level is fixed via the
"NSQ Lv" parameter (NSQ Lv: 0 [min.] ~
255 [max.]).
Prpgm = The squelch threshold level determined via
the dealer programming.
Press the [S
PACE
NSQ Lv: Noise Squelch threshould level
Use the [0] - [9] keys to enter the desired Squelch thresh-
old level directly, and press the [E
ONE
values are 0 (min.) ~ 255 (max.).

Court Blip: Courtesy Blip

When this parameter is set to "on," this function causes
the VXR-7000 to send out a "blip" on the portable/mobile
radio is frequency each time the portable radio is unkeyed.
This provides audible confirmation to the user that the
VXR-7000 was able to receive the transmission from the
portable.
Press the [S
PACE

Rev Bst: Reverse Burst.

When this parameter is set to "on," the CTCSS tone
signal's phase is inverted just before the repeater turns to
receive. This allows the portable/mobile station's CTCSS
Decoder to begin switching off, thus reducing the transi-
tion time required.
Press the [S
PACE

DCS Typ: DCS Format

This command is effective only when DCS is chosen for
squelch control.
A = "Normal" DCS
B = "Inverted" (complement) DCS
Press the [S
PACE
DDec Type: DCS Decoder Type
This command selects the manner in which DCS is to be
decoded.
Fixed = Decodes only the type selected in above pa-
rameter (DCS Typ: Normal or Inverted).
Auto = Both types (Normal and Inverted) will be de-
coded.
Press the [S
PACE
Mode.
] bar to select the desired NSQ Mode.
] key. Available
NTER
] bar to toggle "on" or "off."
] bar to toggle "on" or "off."
] bar to select the desired DCS Type.
] bar to select the desired DCS Decoder