Vertex Standard VXR-7000 Operating Manual

Vertex Standard VXR-7000 Operating Manual

Hide thumbs Also See for VXR-7000:

Advertisement

VXR-7000
Operating Manual
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD ( AUSTRALIA ) PTY., LTD.
Normanby Business Park, Unit 14/45 Normanby Road
Notting Hill 3168, Victoria, Australia

Advertisement

Table of Contents
loading

Summary of Contents for Vertex Standard VXR-7000

  • Page 1 Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VERTEX STANDARD ( AUSTRALIA ) PTY., LTD. Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia...
  • Page 3 Please take a few minutes to read this manual carefully. The information presented here will allow you to derive maximum performance from your VXR-7000. After reading it, keep this manual handy for quick reference, in case questions arise later on.
  • Page 4: Controls And Connectors

    This switch toggles the operating mode between the such as High/Low power selection, as determined “REPEATER” mode and the “BASE” transceiver by your Vertex Standard dealer. The LED above it mode. When the “REPEATER” mode is selected, the glows green when this function is activated. For fur- LED above it glows green.
  • Page 5: Rear Panel

    This DB-25 connector provides a data interface be- When operating from AC mains, a small trickle cur- tween the microprocessor in the VXR-7000 and pe- rent is present at these terminals to maintain bat- ripheral devices (such as the VX-TRUNK Unit).
  • Page 6: Acc Connector Port

    ACC Connector Port Pin 8: RSSI [Analog Output] The VXR-7000 repeater is provided with a 25-pin DB- 25F female connector for interconnections to accesso- A DC voltage proportional to the strength of the sig- ries. Use a DB-25M 25-pin male connector to connect nal currently being received (Receiver Signal accessories to the repeater.
  • Page 7 [Digital Input for the DATA Communications] This pin is intended to be used as a high speed digi- tal data signal input to the repeater. This digital data signal is injected after transmitter splatter filter stage. VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 8: Line Interface Port

    LINE Interface Port Pins 5 & 6: [LINE OUT (Rx Line Audio)] The VXR-7000 is provided with an 8-pin modular jack for line interfacing applications. A Western Electric ® Receiver audio is available from this pair, subject to modular-type RJ45 plug should be used to connect to internal CTCSS or DCS decode if the received sig- this jack.
  • Page 9: Installation

    (mini- Changing the AC input voltage wiring also requires mum) is recommended. Vertex Standard recommends changing the fuse on the FILTER Unit if the voltage is the use of the duplexer. For further details, contact your changed from 100 VAC (100-127 VAC) to 200 VAC (207- Vertex Standard dealer.
  • Page 10: Changing Switching Regulator Unit Ac Mains Jumper Wiring

    Important!: If you change the AC voltage range, you Unit. must also change the AC fuse on the FILTER Unit. Do not replace with a slow-blow type fuse. FILTER Unit Switching Regulator Unit Figure 1 Figure 2 VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 11 Installation Switching Regulator Unit Figure 3 Figure 4 VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 12: Ce27 Programming Software Instruction

    Before connecting the VXR-7000 for programming, turn Before creating the programming data for your off both the computer and the VXR-7000. Now connect VXR-7000 via the CE27 programming software, the CT-29+CT-126 Programming Cable to the computer’s upload the current factory hardware environ- serial port and the VXR-7000’s microphone jack.
  • Page 13 Double-click the left mouse button to toggle “yes” or When this parameter is set to “on,” this function causes “no.” the VXR-7000 to send out a “blip” on the portable/mo- bile radio is frequency each time the portable radio is NSQ Mode: Noise Squelch Mode unkeyed.
  • Page 14 TX Pwr: Transmitter Power Output Selection Action Mode: Select the repeater operation mode This parameter selects the desired power output from the VXR-7000 on the current channel. The available val- Double-click the left mouse button to toggle between ues are HIGH and LOW.
  • Page 15 Guard feature selects “yes” or “no.” When this parameter is set to “yes,” the transmitter in- hibit few second before the repeater is unkeyed. The inhibit time is determined via dealer programming. CE27 Main Screen (Scrolled Right) VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 16: Duplexer Installation

    40 Watts. If the VXR-7000 output power (50 Watts) is in excess of the range of the duplexer's capability, you may reduce the TX output power of the VXR-7000 before installing the Antenna Duplexer, using the following procedure: 5.
  • Page 17 8. Duplexer installation is now complete. Replace the ure 4). front panel back into place, and replace the top and bottom covers. Top Side Bottom Side Figure 1 Bottom Side Bottom Side Figure 2 Figure 3 Figure 4 VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 18: Specifications

    ±5.0 kHz (25 kHz spacing), ±2.5 kHz (12.5 kHz spacing) Modulation Type: 16K0F3E/11K0F3E Audio Distortion: Less than 2.5 % @ 1 kHz Spurious Emissions: Better than 75 dB below carrier Specifications are subject to change without notice or obligation. VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 19: Supplied Accessories

    3U Size 19” Cabinet Rack-Mount Unit CE27 Programming Software CT-29+CT-126 Programming Cable This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. VXR-7000 FM R EPEATER PERATING ANUAL...
  • Page 20 Copyright 2009 No portion of this manual VERTEX STANDARD CO., LTD. may be reproduced All right reserved. without the permission of VERTEX STANDARD CO., LTD. Printed in Japan...

Table of Contents