Napoleon High Country NZ3000 Installation And Operating Instructions Manual
Solid fuel burning zero clearance fireplace
Hide thumbs
Also See for High Country NZ3000:
- Installation and operating instructions manual (48 pages) ,
- Installation and operating instructions manual (48 pages)
Table of Contents
Advertisement
1
THIS FIREPLACE HAS BEEN TESTED AND LISTED BY INTERTEK TESTING SERVICES NA LTD. AS PER THE STANDARDS: CAN/ULC S610, UL 127
FOR FACTORY BUILT FIREPLACES AND TO ULC S639 FOR STEEL LINER ASSEMBLIES FOR SOLID FUEL BURNING MASONRY FIREPLACES.
CERTIFIED UNDER USA ENVIRONMENTAL PROTECTION AGENCY (EPA).
NZ3000
SOLID FUEL BURNING
ZERO CLEARANCE
FIREPLACE
W415-0711 / 10.03.08
$10.00
W415-0711 / 10.03.08
Advertisement
Table of Contents
Related Manuals for Napoleon High Country NZ3000
Summary of Contents for Napoleon High Country NZ3000
- Page 1 THIS FIREPLACE HAS BEEN TESTED AND LISTED BY INTERTEK TESTING SERVICES NA LTD. AS PER THE STANDARDS: CAN/ULC S610, UL 127 FOR FACTORY BUILT FIREPLACES AND TO ULC S639 FOR STEEL LINER ASSEMBLIES FOR SOLID FUEL BURNING MASONRY FIREPLACES. CERTIFIED UNDER USA ENVIRONMENTAL PROTECTION AGENCY (EPA). NZ3000 SOLID FUEL BURNING ZERO CLEARANCE FIREPLACE W415-0711 / 10.03.08...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INtRODUCtION WARNINGS & SAFETY PRECAUTIONS WARRANTY DIMENSIONS INSTALLATION OVERVIEW GENERAL INFORmAtION FEATURES HEATING SPECIFICATIONS ELECTRICAL SPECIFICATIONS PACKING LIST CALIFORNIA PROP 65 EPA COMPLIANCE CARE OF GLASS HI-EFFICIENCY HEATING 2.8.1 HOT AIR GRAVITY VENT SYSTEM (Nz220) 2.8.2 CENTRAL HEATING SYSTEM (Nz62CH) 2.8.3 BLOWER CIRCULATION (Nz64) INStALLAtION PLANNING... -
Page 3: Introduction
WARNING 1.0 iNTrOduCTiON wArNiNgS & SAFETy prECAuTiONS wArNiNgS & SAFETy prECAuTiONS TP - WOOD WARNING W415-0711 / 10.03.08... -
Page 4: Warranty
wArrANTy TP - NAPOLEON - WOOD WARRANTY W415-0711 / 10.03.08... -
Page 5: Dimensions
dimENSiONS FIGURE 1.3a-c iNSTALLATiON OVErViEw This fireplace and its components are designed to be installed and operated as a system. Any altera- tion to or substitution for items in this system, unless allowed by these installation instructions, will void the Warnock Hersey listing and may void the product warranty. It may also create a hazardous installation. -
Page 6: General Information
2.0 gENErAL iNFOrmATiON All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the National Electric Code ANSI/NF No. 70-current (in the United States), or with the current CSA C22.1 Canadian Electric Code (in Canada). This fireplace has not been tested with any vented or unvented gas log set. -
Page 7: Care Of Glass
CArE OF gLASS Hi-EFFiCiENCy HEATiNg To operate this hi-efficiency fireplace as a basic system, the blower is not required, however, to enhance its efficiency a blower is recommended. 2.8.1 HOT Air grAViTy VENT SySTEm (Nz220) All hot air gravity vents must be insulated. May be used to distribute heat to an adjoining room (located either above, or beside the room containing the fireplace) by way of vents, eliminating the need of an additional blower. -
Page 8: Central Heating System (Nz62Ch)
2.8.2 CENTrAL HEATiNg SySTEm (Nz62CH) May be used to heat rooms up to 50 feet from the fireplace. A wall mounted thermostat located in the room to be heated controls the blower supplying warm air from the room containing the fireplace. Consult with a heating specialist to ensure a proper duct layout for your home. -
Page 9: Installation Planning
3.0 iNSTALLATiON pLANNiNg LOCATiON ANd CLEArANCES Do not install into any area having a height less than 7 feet (ceiling of enclosure to fireplace bottom, excluding hearth height). ImPORtANt This fireplace, fully dressed, weighs 575 lbs. Ensure there is adequate floor support for the fireplace, chimney and finishing material. -
Page 10: Combustion Air
COmBuSTiON Air Model NZ3000 has the option of taking outside air directly into the FIGURE 3.2a fireplace through the opening on the left hand side or taking inside air through the lower front grille or a combination of both. Figure 3.2a-b. -
Page 11: Ember Strip And Hearth Extensions
EmBEr STrip ANd HEArTH ExTENSiONS Hearth extensions are to be installed only as described to prevent high temperatures from occurring on con- cealed combustible materials. Hearth ember strips prevent burning or hot particles from inadvertently falling directly on combustible surfaces in the event the building should settle and disturb the original construction. An acceptable 54"... -
Page 12: Hearth Examples
HEArTH ExAmpLES FIGURE 3.4a-d FLUSh hEARth RAISED hEARth RAISED FIREPLACE RAISED hEARth AND FIREPLACE W415-0711 / 10.03.08... -
Page 13: Minimum Clearance To Combustibles
miNimum CLEArANCE TO COmBuSTiBLES mAINtAIN thESE mINImUm CLEARANCES tO COmBUStIBLES: Framed Enclosure: Rear - 0" to stand-offs Sides - 6" Ceiling (Enclosure) - 84" from the base of the fireplace Ceiling (Room) - 84" from the base of the fireplace Chimney - 2"... -
Page 14: Chimney Installation
4.0 CHimNEy iNSTALLATiON FIGURE 4.0a Never install a single wall slip section or smoke pipe in a chase structure. The higher temperature of this single wall pipe may radiate sufficient heat to combustible chase materials to cause a fire. To avoid danger of fire, all instructions must be strictly followed, including the provision of air space clearance between chimney system and enclosure. - Page 15 FIGURE 4.0b-d FIGURE 4.0e TP - 7" CHIMNEY - 2 W415-0711 / 10.03.08...
-
Page 16: Adding Chimney Sections
AddiNg CHimNEy SECTiONS FIGURE 4.1a FIGURE 4.1b TP - ADDING CHIMNEY SECTION W415-0711 / 10.03.08... -
Page 17: Offset Chimney Installation
OFFSET CHimNEy iNSTALLATiON FIGURE 4.2 TP - OFFSET CHIMNEY INSTALLATION W415-0711 / 10.03.08... -
Page 18: Installing Flashing And Storm Collar
iNSTALLiNg FLASHiNg ANd STOrm COLLAr FIGURE 4.3 CONNECTiON TO A mASONry CHimNEy FIGURE 4.4a-b FIGURE 4.4c TP - INSTALLING FLASHING & STORM COLLAR TP - CONNECTION TO A MASONRY CHIMNEY W415-0711 / 10.03.08... -
Page 19: Fireplace Installation
5.0 FirEpLACE iNSTALLATiON FrAmiNg In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the fireplace body, it is recommended that the walls of the fireplace enclosure be “finished” (i.e.: drywall / sheetrock), as you would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity. -
Page 20: Finishing
FiNiSHiNg Use only a non-combustible material to finish the face of the fireplace. A non-combustible material such as cement board is required for this purpose. Ventilation openings are required in enclosures up to 96" high. They are recommended for all enclosures. Above 84"... -
Page 21: Enclosure Ventilation
ENCLOSurE VENTiLATiON FIGURE 5.3a NOtE: As an alternate to grates a 1" x 40" wide gap can be left in the bottom and top of any finishing material to circulate the air from the floor, around the fireplace and out the top. FIGURE 5.3b W415-0711 / 10.03.08... -
Page 22: Minimum Mantel Clearances
miNimum mANTEL CLEArANCES Facing, mantel and / or finishing materials must not interfere with air flow through air openings, louvres, operation of louvres or doors or access for service. An optional combustible mantel must be a minimum of 12" above the top of the faceplate and not to extend more than 2"... -
Page 23: Fireplace Finishing
Operation of the fireplace without the baffles can result in excessive temperatures that could damage the fireplace, chimney and the surrounding enclosure. The NZ3000 contains two identical baffle pieces. Lay the first piece to the back of the fireplace on top of the Secondary Air Tubes and interlock the second piece as illustrated. -
Page 24: Face Plate, Upper Grille, Keystone And Door Installation
FACE pLATE, uppEr griLLE, kEySTONE ANd dOOr iNSTALLATiON 6.2.1 rEmOVE TEmpLATE (ONCE All THE FINISHED FACINg MATERIAl HAS bEEN INSTAllED) 1. Remove the screws, template, and discard. FIGURE 6.2.1 6.2.2 FACEpLATE, HiNgE, ASH Lip ANd Air CONTrOL Arm iNSTALLATiON NOtE: The faceplate is shipped with the upper and lower grilles assembled. Remove both grilles be- fore proceeding. -
Page 25: H336-Wi Door Assembly
6.2.3 H336-wi dOOr ASSEmBLy Install hardware as shown in the order of 1 through 4. NOtE: Doors may need to be adjusted to ensure air tightness. FIGURE 6.2.3b FIGURE 6.2.3a LEFt DOOR RIGht DOOR ASSEmBLy ASSEmBLy ** The final angle of the left door handle should mirror the right door handle in the closed position. Tighten the nut to secure the handle at the desired angle. -
Page 26: Optional Spark Screen Installation
6.2.5 OpTiONAL SpArk SCrEEN iNSTALLATiON Never leave fireplace operating unsupervised with spark screen in place. Use caution when placing this spark screen on an operating fireplace. Turn off the blower before operating with the spark screen. Use only Wolf Steel approved optional accessories and replacement parts with this appliance. Using non-listed accessories and replacement parts (blowers, doors, louvres, trims, gas components, vent components, etc.) could result in a safety hazard and will void the limited lifetime warranty. -
Page 27: Optional Nz64 Blower Installation
OpTiONAL Nz64 BLOwEr iNSTALLATiON All wiring should be done by a qualified electrician and shall be in compliance with local codes and with the National Electric Code ANSI/NF No. 70-current (in the United States), or with the current CSC22.1 Canadian Electric Code (in Canada). This fireplace is supplied with two micro (pressure) switches (the blower on high draws 3.0 amps using 120V (approx. - Page 28 One black wire - connects to power "L2" (neutral lead). One green wire - connects to ground. One white wire - connects to KB-35 rheostat (not supplied) See above. FIGURE 6.3c-2 FIGURE 6.3d vENt CONNECtION FIGURE 6.3e D. Connect the 6” liner to the 6" fireplace collar and blower collars.
-
Page 29: Nz64 Blower Replacement
Nz64 BLOwEr rEpLACEmENT FIGURE 6.4a FIGURE 6.4b FIGURE 6.4c FIGURE 6.4d FIGURE 6.4f TP - Nz64 BLOWER REPLACEMENT W415-0711 / 10.03.08... -
Page 30: Operating Instructions
7.0 OpErATiNg iNSTruCTiONS Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected. tIPS FOR BURNING: • Create a large fire to heat up the fireplace before adjusting to a slower burn. • To create a large, quick burning fire, use small pieces of wood. •... -
Page 31: Draft Control
drAFT CONTrOL Always operate this fireplace with the door closed and latched except during start-up and re-fueling. Draft is the force which moves air from the fireplace up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other forces. Adjusting the draft control regulates the temperature. - Page 32 G. As soon as the doors are closed, you will observe a change in the FIGURE 7.5g flame pattern. The flames will get smaller and lazier because less OPERAtING WIth DOOR CLOSED oxygen is getting into the combustion chamber. The flames, however, are more efficient.
-
Page 33: Fuel Loading And Burn Cycle
FuEL LOAdiNg ANd BurN CyCLE The bricks will be nearly all white and the glass mostly clear. The whiteness of the bricks and the cleanness of the glass are good indicators of your operating efficiency. Not enough heat is produced when only one or two pieces of wood are burned. A minimum of three pieces are needed to encase a bed of coals that sustains the fire. -
Page 34: Overnight Burn
OVErNigHT BurN A. Get the fireplace hot by moving the air control to high and letting the fireplace burn for 15 minutes. FIGURE 7.9 B. Load your larger pieces of wood compactly, packed close enough to prevent the flames from penetrating it completely. C. -
Page 35: Maintenance
8.0 mAiNTENANCE ruN-AwAy Or CHimNEy FirE A chimney fire can permanently damage your chimney system. This damage can only be repaired by replacing the damaged component parts. Chimney fires are not covered by the lifetime limited warranty. CAUSES: 1. Using incorrect fuel, or small fuel pieces which would normally be used as kindling. 2. -
Page 36: Creosote Formation And Removal
FIGURE 8.3c FIGURE 8.3a-b CrEOSOTE FOrmATiON ANd rEmOVAL FIGURE 8.4 When wood is burned slowly, it produces tar and other organic vapours which combine with expelled moisture to form creosote. These vapours condense in the relatively cooler chimney flue of a slow burning fire and when ignited, make an extremely hot fire. -
Page 37: Replacements
9.0 rEpLACEmENTS FIREPLACE AND ACCESSORy REPLACEmENt PARtS PARt NUmBER DESCRIPtION W300-0103 DOOR GLASS W562-0049 DOOR GASKET 7/8 W562-0050 DOOR GASKET - CENTRE 5/8 W010-1933 GLASS & GASKET W690-0005 120V THERMOSTAT W090-0146 BRICK, FRONT LEFT W090-0147 BRICK, FRONT SIDE (2PC REQUIRED) W090-0148 BRICK, SIDE (2PC REQUIRED) W090-0149... - Page 38 ACCESSORIES PARt NUmBER DESCRIPtION H336-WI ARCHED DOUBLE DOORS - WROUGHT IRON FINISH FPWI3 FACEPLATE ARCHED - WROUGHT IRON FINISH NSK3 ARCHED SPARK SCREEN KIT Nz220 GRAVITY HOT AIR VENT KIT NM228-M FLUE TILE SUPPORT Nz64 BLOWER KIT Nz62CH CENTRAL HEATING SYSTEM W415-0711 / 10.03.08...
-
Page 39: Trouble Shooting Guide
10.0 TrOuBLE SHOOTiNg guidE TP - TROUBLE SHOOTING_WOOD W415-0711 / 10.03.08... -
Page 40: Rating Plate Location
11.0 rATiNg pLATE LOCATiON W415-0711 / 10.03.08... -
Page 41: Fireplace Service History
12.0 FirEpLACE SErViCE HiSTOry TP - SERVICE HISTORY W415-0711 / 10.03.08... -
Page 42: Notes
13.0 NOTES NOTES TP - NOTES W415-0711 / 10.03.08...