When Using The Web Browser - TEC B-SP2D Series Maintenance Manual

7. WIRELESS LAN PARAMETER SETTING

7.2 WHEN USING THE WEB BROWSER

It is possible to access the printer's website at "http://[printer's IP address]/" by using the web browser. From
this website, the wireless LAN parameters can be set.
There are the Info, Wireless, IP Addr, and Admin tabs on the web page. On each page, it is possible to browse
and set the parameters.
The URL, http://[printer's IP address]/maintenance.html, allows an access to the printer maintenance web
page. On this page, the country where the printer is used and UART baud rate can be set.
For details, refre to the following sections.
7.2.1 Wireless Parameter Print
First, print the wireless LAN module's parameter setting before setting the parameters.
Pressing and holding the Power button while the printer power is off causes the printer to turn on and print a
wireless LAN parameter settings label regardless of the issue mode. If the label is not printed successfully due
to an error, it is required to turn off the power, and then retry from the beginning. This is because the printer
will not print the label even if the error is cleared.
Although the wireless LAN parameter settings label is also printed by sending a reset command while holding
down the Power button of the printer in operation, these printed parameter settings are not effective. There-
fore, the parameter settings label must be printed when the printer power is off.
Sample
Item
Module Version
IP IP Address
GW Gateway IP Address
SUB Subnet Mask
SOCK Socket communication
Socket port
TYPE Country where the printer is used.
LPR LPR communication
DHCP DHCP
CON Connection mode
AUTH Authentication method
WEP WEP
SECU Security mode
CHAN Used channel
WINS WINS
HOST Host name
ESSID ESS ID
IP Address
Barcode
NOTE: LEAP is selectable for the security mode only when the wireless LAN module version is V1xx.
RF-LAN PARAMS[100]
IP [172.016.000.010]
GW [000.000.000.000]
SUB [255.255.000.000]
SOCK [ON ][65535]
WEP [128]|SECU[MD5] |CHAN[07]
WINS [ON ][000.000.000.000]
HOST [TTEC
[
ESSID [TEC
[
MAC:0010C61CCDA9
Parameter
Version
|TYPE[EU ]
|LPR [ON ]
|DHCP[ON ]
|CON [INF]
|AUTH[SKEY]
]
]
]
]
Setting
xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx
ON/OFF
0 to 65535
EU/US/JP/FRA/ESP
ON/OFF
ON/OFF
Infrastructure/Adhoc
Open system/Shared key
OFF/ON (40 bits)/ON (128 bits)
OFF/MD5 /LEAP
0 to 14
OFF/ON (STATIC)/ON(DHCP)
xxx.xxx.xxx.xxx
xxxxxxxx... (Max. 32 bytes)
xxxxxxxx... (Max. 32 bytes)
xxx.xxx.xxx.xxx
7-10
EO18-33014
(Revision Date: Oct. 26, 2004)
7.2 WHEN USING THE WEB BROWSER
Print
[xxx]
[xxx.xxx.xxx.xxx]
[xxx.xxx.xxx.xxx]
[xxx.xxx.xxx.xxx]
[ON ] [OFF]
[00000] to [65535]
[EU ] [US ] [JP ]
[FRA] [ESP]
[ON] [OFF]
[ON ] [OFF]
[INF][ADH]
[OPEN] [SKEY]
[OFF][ 40] [128]
[OFF ] [MD5 ] [LEAP]
[00] to [14]
[OFF ] [ON ] [DHCP]
[xxx.xxx.xxx.xxx]
[xxxxxxxx...]
[xxxxxxxx...]
A bar code is printed.