Specifications - Alpine CDA-105E Owner's Manual

01GB00CDA105E.book Page 33 Thursday, November 6, 2008 2:22 PM
Indication for iPod Mode
• The iPhone/iPod is not connected.
- Make sure the iPhone/iPod is correctly connected (refer to
"Connections" on page 37).
Make sure the cable is not bent excessively.
• There are no songs in the iPhone/iPod.
- Download songs to the iPhone/iPod and connect to this unit.
• Communication error.
- Turn the ignition key off, and then set to ON again.
- Reset the iPod.
- Check the display by reconnecting between the iPhone/iPod
and this unit, using the iPhone/iPod cable.
• Caused by the iPhone/iPod Software Version not being
compatible with this unit.
- Update the iPhone/iPod Software Version to be compatible
with this unit.
• The iPhone/iPod is not verified.
- Change another iPhone/iPod.
• Abnormal current is run to the USB connector device.
- You can solve the problem by switching the source, turning the
unit power off, or ACC to the OFF position.
• A USB device that is not supported by the unit is connected.
- Connect a USB device that is supported by the unit.
Indication for all Modes
• Malfunction occurred as a result of the speaker cable shorting on
the car chassis.
- Route the cable correctly, and set POWER IC to ON (page 16).
If the above solution does not work, consult your nearest
dealer.
01GB05CDA105E.fm

Specifications

FM TUNER SECTION
Tuning Range
Mono Usable Sensitivity
50 dB Quieting Sensitivity
Alternate Channel Selectivity
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
AM TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
CD PLAYER SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
USB SECTION
USB requirements
Max. Power Consumption
USB Class
File System
MP3 Decoding
WMA Decoding
AAC Decoding
Number of Channels
Frequency Response*
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
* Frequency response may differ depending on the encoder
software/bit rate.
PICKUP
Wave length
Laser power
GENERAL
Power Requirement
Maximum Power Output
Maximum Pre-Output Voltage
Bass
Treble
Weight
CHASSIS SIZE
Width
Height
Depth
NOSEPIECE SIZE
Width
Height
Depth
• Due to continuous product improvement, specifications and design
are subject to change without notice.
ALPINE CDA-105E 68-09359Z81-A (EN)
87.5-108.0 MHz
9.3 dBf (0.8 µV/75 ohms)
13.5 dBf (1.3 µV/75 ohms)
80 dB
65 dB
35 dB
2.0 dB
531-1,602 kHz
22.5 µV/27 dB
5-20,000 Hz (±1 dB)
Below measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
USB 1.1/2.0
500 mA
Mass Storage
FAT 12/16/32
MPEG-1/2 AUDIO Layer-3
Windows Media™ Audio
AAC-LC format ".m4a" file
2-Channel (Stereo)
5-20,000 Hz (±1 dB)
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
795 nm
CLASS I
14.4 V DC
(11-16 V allowable)
50 W × 4
2 V/10 k ohms
±14 dB at 100 Hz
±14 dB at 10 kHz
1.5 kg (3 lbs. 4 oz)
178 mm (7)
50 mm (2")
160 mm (6-1/4")
170 mm (6-3/4")
46 mm (1-13/16")
24 mm (15/16")
33
-EN