Turning Mute Mode On/Off (Int Mute); Setting The Aux+ Setup Mode; Setting The Aux+ Level (Aux In Gain); Setting The External Digital Input - Alpine CDA-105E Owner's Manual

01GB00CDA105E.book Page 17 Thursday, November 6, 2008 2:22 PM
POWER IC ON: The speakers are driven by the built-in
amplifier.
SPEAKER
RIGHT FRONT
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
• No sound is produced by the system when the POWER IC is set to
OFF.

Turning Mute Mode On/Off (INT MUTE)

MUTE ON / MUTE OFF (Initial setting)
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from the
device.

Setting the AUX+ SETUP Mode

AUX+ ON / AUX+ OFF (Initial Setting)
You can input the audio of an external device, (such as a Portable audio
player) to the Bluetooth interface connector of this unit. A special
Conversion cable (KCE-237B) is necessary to adapt the Bluetooth
interface connector as an AUX IN.
A portable music device and a Bluetooth INTERFACE (KCE-400BT)
cannot be connected to the Bluetooth I/F connector at the same time.
AUX+ ON: Set to ON when a portable device is connected. If
SOURCE/
sound of the portable device is input to the unit.
AUX+ OFF: When set to OFF, AUX+ source cannot be selected.
You can change the AUX+ NAME display when AUX+ SETUP is set to
ON. Press /ENT when AUX+ SETUP is set to ON, and select
AUX+ NAME by turning the Rotary encoder, then press
After that, turn the Rotary encoder to select the desired AUX+ NAME.

Setting the AUX+ Level (AUX IN GAIN)

LOW (Initial setting) / HIGH
After setting to ON in "Setting the AUX+ SETUP Mode", this setting
can be carried out.
LOW: Decreases the external input audio level.
HIGH: Increases the external input audio level.
01GB05CDA105E.fm
Speakers
Front
right
Rear
right
Rear
left
Front
left
is pressed and AUX+ is selected, the
/ENT.

Setting the External Digital Input

D-AUX ON / D-AUX OFF (Initial setting)
When an ALPINE Ai-NET compatible digital audio processor
(PXA-H701) and a DVD player (DVE-5207) not compatible with
Ai-NET are connected, set D-AUX to ON to enjoy 5.1-channel
surround sound.
You can change the D-AUX NAME display when D-AUX is set to ON.
Press /ENT when D-AUX is set to ON, and select D-AUX NAME
by turning the Rotary encoder, then press
the Rotary encoder to select the desired D-AUX NAME.
• Press SOURCE/ , and select the DIGITAL-AUX mode, and adjust
the volume, etc.
• After input selection is completed, turn the ignition off and back on
again. Setting of the optical digital input switch is completed.
• Depending on the connected audio processor, DVD player sound
may continue to be output, even though the source is changed to
another one. If this occurs, set the DVD player's power to OFF.

Setting the AUX Mode (V-Link)

AUX IN ON / AUX IN OFF (Initial setting)
You can input TV/video sound by connecting an optional Ai-NET/RCA
Interface cable (KCA-121B) or Versatile Link Terminal (KCA-410C) to
this component.
You can change the AUX name display when AUX IN is set to ON.
Press /ENT when AUX IN is set to ON, and select AUX NAME by
turning the Rotary encoder, and then press
After that, turn the Rotary encoder to select the desired AUX name.
If the KCA-410C is connected, it is possible to select two AUX names.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/
then press BAND to select your desired device.
ALPINE CDA-105E 68-09359Z81-A (EN)
/ENT. After that, turn
/ENT.
to select AUX mode and
17
-EN