Rotary, cylindrical and boost manual steering rider scrubber (68 pages)
Summary of Contents for Clarke 32IX-00320A
Page 1
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or other property could occur as well.
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
Page 4
Do not use this machine as a step or furniture. Do not ride on this machine. CAUTION: Your machine warranty will be voided if anything other than genuine Clarke parts are used on your machine. Always use Clarke parts for replacement.
Introduction & Machine Specifications Clarke’s newly designed Vision 38, 32 & 26 automatic scrubbers are efficient and superior floor cleaning machines. The Vision 38 uses two brushes or pads to scrub a path 38 inches wide. The Vision 32 uses two brushes or pads to scrub a path 32 inches wide.
10. As the machine begins to travel down the ramp, push the control handles toward the machine to maintain a slow downward speed. 11. Replace squeegee assembly, brush housings, & brushes or pad drivers after the machine is unloaded and ready to use. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 7 -...
Page 8
Warning (Also used on IX Models) Power (Also used on IX Models) On/Off Key Switch (Also used on IX Models) Traverse Speed Solution Control (Also used on IX Models) Brush Up/Down Page -8- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
SYMBOLS USED ON VISION 32 IX & 26 IX Squeegee/Vacuum Traverse Speed Control Brush Pressure Brush Up/Down Increase/Decrease Brush Pressure Meter Battery Meter Hour Meter Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 9 -...
Turn the key switch "ON", and try again. An authorized service person should be contacted if the breaker trips again. F G H I J Page -10- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
Hour Meter (See Figure #2, Item "J") The hour meter indicates the number of hours the machine has operated. It runs only when the machine is moving forward or reverse. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 11 -...
Page 12
Turn the key switch "on" and try again. Contact an authorized service person if the breaker trips again. K L M Figure #2 Figure #3 Figure #4 Page -12- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
(Figure #7a). To release the brake, lift pedal up (Figure #7b). CAUTION: Do not activate the brake while the machine is moving. Figure #6. Figure #7a. Figure #7b. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 13 -...
9. Install the tank, reconnecting hoses and replace the two screws attaching the solution tank to the rear of the frame. NOTE: Charge the batteries before using the machine. Figure #9 Page -14- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
To clean the teminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicarbonate of soda to get into batteries. Keep the batteries charged. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 15 -...
For more instruction on the use of the charger, read the instruction book supplied with the charger. Figure #13 Page -16- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
4. Turn the key switch "OFF". 5. Go to the front of the machine. 6. Push down on two sides of the brush or pad driver until the gimbals release. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 17 -...
3. Add a cleaning chemical to the water. for the correct amount, follow the directions shown on the container. 4. Replace the solution tank lid. Figure #16 Figure #17 Page -18- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
Page 19
8. To turn the machine, push the rear of the machine to the side. 9. When you stop the machine, turn the key switch "OFF". 10. Set the parking brake. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 19 -...
5. Leave the solution on the floor long enough for the solution to begin cleaning the floor. 6. Scrub the floor again with additional solution, picking up all the solution with the squeegee Page -20- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
Have an authorized service person repair the The charger is damaged. charger. Check voltage of each cell while discharging. The battery is defective. Connect the batteries. The batteries are disconnected. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 21 -...
Page 22
The machine loses power. Check wire connection to traverse motor. Replace the fuses. Check the batteries connections. NOTE: If the motors continue to stop, consult an authorized service person. NOTES Page -22- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
7. Make sure the brushes are in position and installed correctly 8. Check the installation of the squeegee and squeegee hose. Figure #23 Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 23 -...
Page 24
Use a clean cloth and wipe the surface of the machine. Charge the batteries. See the instruction in the section of Figure #23d this book called “How To Charge The Batteries”. Page -24- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
Page 25
5. Use a grease gun to lubricate the drive wheel and the casters. See figure #25. 6. Apply a thin lubricant to the drive chain. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 25 -...
Page 26
"Y" up. Make very small adjustments and try it until a uniform flare is achieved. Changing the tilt may also require readjusting the squee- gee pressure. Figure #28 Page -26- Clarke Owner's Manual -Vision 38 I\32 I/IX - 26 I/IX...
Page 27
(Figure #30) and remove the filter screen (Figure # 31) and clean or replace it. Push filter assembly back inside frame. Figure #31 Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 27 -...
883351 Grease Fitting x x x x x 59944R Wheel Assembly x x x x x 170892 Washer, Lock ¼ x x x x x Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 35 -...
81207A Nut, -16 SS x x x 419702 Wheel x x x 61242A Tube Bracket x x x 170915 Screw, ¼-20 x x x x Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 39 -...
NOTE: * #60 used only as needed to square up linkage bars (item # 29) NOTE: indicates a change has taken place since last publication of this manual. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 41 -...
NOTE: * #61 used only as needed to square-up linkage bars (item 29) ◆ NOTE: indicates a change has taken place since last publication of this manual. Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 43 -...
Squeegee Hose x x x x x 38945B Recovery Tank 170915 Screw, ¼-20 x x x x 30410A Hose, Vac Motor x x x x x Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 45 -...
Helical Washer x x x 50515A Thru Bolt x x x 44809A Shaft Key x x x 54238A B.E. Bracket Assembly (Gear Box) x x x Clarke Owner's Manual - Vision 38 I/32 I/IX - 26 I/IX - 49 -...
Clarke Vision 38 I - 32 I - 26 IX Gear Box #54238A 11/93 Ref # Part No. Description 57846A Ring, Snap 58143A Seal, Oil, Small 52050A Cap End 56668A O'Ring 51176A Bearing, Large 58316A Shaft & Gear, Gearbox 902605...