Table of Contents
Advertisement
Inp_3_Mode – the current input 3 mode, 0 – SDI, 1 – DVI;
Link_Flags – Master user settings link flags, it may be unlinked(value 0) or linked(value1) to the corresponding
basic parameter:
bit 7 – input 0 settings link flag (brightness, contrast, saturation),
bit 6 – input 1 settings link flag (brightness, contrast, saturation),
bit 5 – input 2 settings link flag (brightness, contrast, saturation),
bit 4 – input 3 settings link flag (brightness, contrast, saturation),
bit 3 – input 4 settings link flag (brightness, contrast, saturation),
bit 2 – position and numbers of the Logo 1, Logo 2 and Clock position link flag,
bit 1 – PiP position and size link flag,
bit 0 – input 3 mode link flag;
Link_Flags_Ext – Master User settings extended flags, it may be unlinked (value 0) or linked (value 1) to the
corresponding basic parameter:
bit 7 – output signal system link flag,
bit 6 – multiscreen resolution link flag,
bit 5 – Luma Key threshold level link flag,
bits 4... 0 reserved, ignore;
Flags_Mixer – switching flags (mixing):
bit 7 – Line connected to Program output (Main Source), 0 – Line A, 1 – Line B,
bit 6 – reserved, ignore,
bit 5 – reserved, ignore,
bit 4 – switch mode, 0 – mixing, 1 – curtains,
bits 3... 0 reserved, ignore;
Flags_Line_A, Flags_Line_B – Frame freeze flags of Line A and Line B:
bit 7 – 0 - Frame freeze off, 1 - Frame freeze on
bits 6... 0 – reserved, ignore;
Flags_Sources_Position – Selection Key inversion flags and switcher's T-bar mode flag:
bit 7 – 0 – keyboard's source Selection Keys are arranged in direct manner (Source 1 is on the left),
1 – inverse manner (Bar is on the left),
bit 6 – 0 – T-bar is active only while moving upwards, 1 – T-bar is active while moving both upwards and
downwards,
bits 5... 0 reserved, ignore;
Flags_DSK – PiP and Luma Key out flags:
bit 7... 6 – reserved, ignore,
bit 5 – 1 – Luma Key is output onto Preview channel, 0 – not,
bit 4 – 1 – Luma Key is output onto Program channel, 0 – not,
bit 3 – 1 – PiP is output onto Preview channel, 0 – not,
bit 2 – 1 – PiP is output onto Program channel, 0 – not,
bits 1... 0 – reserved, ignore;
Flags_Lbl – Logo and Clock activation flags:
bit 7 – 1 – Logo 1 is output onto Program channel, 0 – not,
bit 6 – 1 – Logo 2 is output onto Program channel, 0 – not,
bit 5 – 1 – Logo 1 is output onto Preview channel, 0 – not,
bit 4 – 1 – Logo 2 is output onto Preview channel, 0 – not,
bit 3 – Clock activation instead of Logo 2 (0- Logo 2, 1- Clock),
bits 2... 0 – reserved, ignore;
1.26. COM = 0xA0 – copy and write setting parameters Common_Settings (Section 2) from the device's
EEPROM into the device's volatile memory. ARG = 0. Device replies with LEN = 0, ANSW is not available.
1.27. COM = 0xA0 – device soft reset. ARG = 0. Device replies with LEN = 0, ANSW is not available. The device
executes soft reset and it completely reboots (similar to the power recycle). It is impossible to establish a
connection with the device for around 8 seconds.
37
Advertisement
Table of Contents
