Related Manuals for Jøtul C 450
Summary of Contents for Jøtul C 450
- Page 1 138344_Rev_D - C450 Kennebec 8.2.10 Jøtul C 450 Fireplace Insert Installation and Operating Instructions for the United States & Canada Keep these instructions for future reference.
- Page 2 138344_Rev_D - C450 Kennebec 8.2.10 NOTICE: YOU SHOULD CONSULT THE AUTHORITY HAVING JURISDICTION IN YOUR LOCALE (SUCH AS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE PREVENTIOIN BUREAU, ETC.) BEFORE INSTALLATION TO DETERMINE THE NEED TO OBTAIN A PERMIT. Accepted For Use City of New York Department of Buildings MEA # 368-04-E...
-
Page 3: Table Of Contents
C 450 Surround Assembly .........6 the firebox. You may also wish to attach your sales receipt to this manual for future reference. Installation Model: Jøtul C 450 Fireplace Insert Masonry Fireplace Requirements ......7 Factory-built Fireplace Requirements ....7 Chimney Height ............7 Serial Number: Clearance to Combustibles ........8... -
Page 4: Standards And Safety Notices Standards / Codes
Check Building Codes Standards & Approvals When installing, operating and maintaining this The Jøtul C 450 Fireplace Insert has been tested and fireplace insert, follow the guidelines presented listed to: U.S.: ANSI/UL 1482 in these instructions, and make them available to Canada: CAN/ULC-S628-93 anyone using or servicing the stove. -
Page 5: Safety Notices
• BURN SOLID WOOD FUEL ONLY We strongly urge you to have your authorized Jøtul • DO NOT USE CHEMICALS OR FLUIDS TO dealer install your new Jøtul C 450 Fireplace Insert. START THE FIRE. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS. -
Page 6: Specifications
138344_Rev_D - C450 Kennebec 8.2.10 Jøtul C 450 Specifications 29” 737 mm Performance 25 1/2” 635 mm Fuel: 20” Logs Heat Output 50,000 BTU/hr. (4.1 kg/hr.) Firebox Heating Capacity : 1,100 - 1,600 sq. ft. 16 3/4” Overall Efficiency : 71% 25 1/4”... -
Page 7: Installation
• Air flow within and around the fireplace shall not smoke shelf and adjacent damper frame area be altered by installation of the insert. The C 450 to accommodate installation of a chimney liner, Surround Panels comply with this requirement. -
Page 8: Clearance To Combustibles
138344_Rev_D - C450 Kennebec 8.2.10 Clearance to Combustible Materials • There may be no combustible materials located MANTEL AREA anywhere within 36” (914 mm) of the front of the fireplace insert. This precaution includes items such as drapes or doors that could swing into the area 3.5”... -
Page 9: Hearth Protection
138344_Rev_D - C450 Kennebec 8.2.10 24 1/2” (622 mm) 20 1/2” from face (521 mm) from face 2 1/2” 6 1/2” (64 mm) (165 mm) 18” 18” (457 mm) Firebox Firebox (457 mm) from door Sleeve opening Sleeve from door opening Figure 10. -
Page 10: Chimney Connection
138344_Rev_D - C450 Kennebec 8.2.10 Chimney Connection A positive connection must be made between the fire- Installation place insert and the chimney by one of the following 1. Remove the existing damper and linkage compo- approved methods. nents from the fireplace. Alternatively, you can In the U.S: wire the damper plate to lock it in the open posi- The insert is connected to a listed stainless steel flexible... -
Page 11: Installing The Firebox
138344_Rev_D - C450 Kennebec 8.2.10 Installing the Firebox 1. If appropriate, use 3” flexible noncombustible duct to connect an outside air inlet to the air inlet collar at the back of the firebox. 2. With assistance, move the firebox into position within the fireplace and align the insert flue collar with the Adaptor Collar. -
Page 12: Kennebec Surround Assembly
138344_Rev_D - C450 Kennebec 8.2.10 Left Breast- plate Tools Required: • 10 mm socket or wrench Right Breast- M6 x 12 Flange Bolt plate M6 x 10 Flange Bolt Right Leg Set Screw Left Leg M6 x 10 Flange Bolt M6 x 12 Flange Bolt Trim Rod M6 x 10 Flange Bolts... -
Page 13: Tamarack Surround Assembly
138344_Rev_D - C450 Kennebec 8.2.10 Tools Required: M6x16 Hex Head Bolts • 10 mm socket or wrench Grille Shade Center Breast- plate Right Breast- Trim Rod Left plate Breastplate Hang Tab should point straight down Right Leg Left Leg Figure 12a. Tamarack Lattice Surround Panel Assembly Tamarack Surround Assembly All fasteners have already been installed in the appro- 5. -
Page 14: Blower Assembly
138344_Rev_D - C450 Kennebec 8.2.10 Hardware Bag Contents: 1. Power Switch 2. Power Cord Receptacle 3. Snapstat Extension Assembly 4. Air Deflector 5. #8 x 1/2” sheet metal screws, 4 6. Ground jumper wire 7. Power Cord Tools Required: • safety gloves and goggles •... -
Page 15: Blower Operation
138344_Rev_D - C450 Kennebec 8.2.10 Install the Ashlip Extension Assembly The assembly is comprised of a steel Extension Base and a cast iron Ashlip plate. The procedure is the same for double door and single door fireboxes. 1. Engage the three spring clips on the Extension Base with the adjoining cutouts on the firebox base. -
Page 16: Operation
138344_Rev_D - C450 Kennebec 8.2.10 Operation Read the following section carefully before building a fire WARNING: in your Jøtul C 450 Fireplace Insert. OPERATE THIS FIREPLACE INSERT ONLY WITH Fuel THE FRONT DOOR(S) FULLY CLOSED. A PARTIALLY OPENED DOOR MAY RESULT IN OVER-FIRING. ALSO, This stove is designed to burn natural wood ONLY. -
Page 17: Starting / Maintaining The Fire
Starting and Maintaining a Fire Creosote Formation Burn only solid wood directly on the firebrick of the The Jøtul C 450 is designed to burn wood cleanly stove. Do not elevate the fire in any way. and efficiently when operated as described in this manual. -
Page 18: Maintenance
The container of ashes should be placed on a non- GLASS SPECIFICALLY DESIGNED FOR THE combustible floor or on the ground, well away from all JØTUL C 450 FIREPLACE INSERT: combustible materials, pending final disposal. If the PART #220356 (TWO) - FOR DOUBLE DOORS... -
Page 19: General Maintenance
Regular maintenance will assure proper perfor- Check door and glass gaskets for seal integrity. mance and prolong the life of your Jøtul C 450. The gaskets should be soft enough to be somewhat The following procedures do not take long and are resilient to the touch. -
Page 20: Illustrated Parts Breakdown
138344_Rev_D - C450 Kennebec 8.2.10 Jøtul C 450 Fireplace Insert Illustrated Parts Breakdown Tamarack Lattice Style Surround Assembly Kennebec Classic Style Surround Assembly 24 25... -
Page 21: Parts List
138344_Rev_D - C450 Kennebec 8.2.10 Jøtul C 450 Parts List No. Description Part Number Refractory Brick, (13) 129082 Control Door, Crosshatch Grille - Matte Black 10398092 Refractory Brick, 9” x 2” (2) 220390 Control Door, Crosshatch Grille - Blue Black 10398027 Refractory Brick, 1 5/8”... -
Page 22: Alternate Floor Protection
138344_Rev_D - C450 Kennebec 8.2.10 Appendix A: Alternate Floor Protection Definitions: All floor protection materials must be non-combus- Thermal Conductance = tible i.e.. metal, brick, stone, or mineral fiberboards. No combustible material may be used to protect the floor in (Hr)(ft2)(f) (m2)(k) front of the fireplace insert. - Page 23 138344_Rev_D - C450 Kennebec 8.2.10 Jøtul Wood Product Warranty 4) Damage due to service performed by an installer or service agency, unless otherwise agreed to in writing by JØTUL. This warranty policy applies to wood-burning products identified 5) Damage caused by unauthorized modification, use or repair. by Jøtul and Scan trade names, as set forth below.
- Page 24 138344_Rev_D - C450 Kennebec 8.2.10 This appliance must be installed in conformance with local and national building regulations. It is important that the these instructions be carefully read and understood before beginning the instal- lation. Jøtul pursues a policy of continual product development. Consequently, products may differ in specification, color or type of accessories from those illustrated or described in various publications.