Table of Contents
Advertisement
TEST POINT
MAIN PWB
R5076
R5077
C5039
R5078
C2055
R3026
R2044
R2048
C3011
R5071
R3027
Q3005
R3024
R5070
C3012
C3013
R3023
TP1907
R3028
Q3006
R3025 R3022
R3031
C3024
R3032
R3041
C3025
R3040
R3043
R3042
C3020
R3039
R3038
C3019
R5074
C3009
R3036
R3044
R3046
R3037
C3028
R3048
L3003
C3017
C5040
R5082
R3033
R3050
R5084
R5087
R5085
TP1904
C2014
PR1904
R1906
R5063
C1907
R1912
R5039
C5019
R1904
C1903
C5021
R1970
R1903
R1977
R1979
R1968
C5020
R5048
R5045
R1965
R5049
R1976
R1963
C1962
C2041
LX-P1010ZU/ZE
LENS SIDE
R5017
R3003
R3005
R5015
R3008
R3007
R5011
R5019
R5013
R5016
R3009
R3004
R5020
C5052 R5053
C5008
C5016
IC4001
Q4008
C4014
R4035
D4008
D4006
C5015
FL2006
R3570
FL2015
FL2007
R3569
FL2016
R3568
R3601
R3567
R3602
R3566
FL2008
R3603
R3565
R3604
R3564
R3605
R3606
TP3505
R3502
R3607
R3503
R3608
R3504
R3505
R3609
TP3501
R3507
R3508
R2002
R3509
R2001
R3594
R3516
R3595
R3596
C3503
R3597
C2002
R5034
R3598
D3504
R3527
R3599
R3515
C3506
R5027
Q5008
R3525
L5002
R3528
C5011
D3506
C3507
Q5026
R3538
R3530
R3523
R5029
Q5028
C3505
R3539
R3518
R3519
R3520
R3517
R3588
C3579
R3590
C3520
C3521
R2060
C3522
R2061
C3523
C3534
R3584
R2065
C3535
R2062
C3524
L2022
R3583
C3536
C3525
C3537
R3582
C3538
C3540
C3539
C3573
C3541
R3581
R3548
R3561
R3580
R3579
C3519
L2009
C3565
R3578
L2002
C2020
R2005
C2021
C2010
R2245
R2253
R2254
R2247
R2248
C2155
R2200
C2133
D2001
R2087
C2131
D2002
R2025
C2124 C2125
L2024
R2293
C2007
R2258
R2295
R2294
L2017
L2004
C2030
R2262
R2284
TP2073
TP2067
R2122
TP2070
R2109
TP2068
R2114
TP2062
R2265
R2267
TP2075
TP2057
TP2074
TP2061
R2154
TP2069
TP2063
TP2060
R2155
TP2066
R2139
R2157
R2158
TP2056
R2182
C2098
R2151
R2113
R2312
R2130
R2034
R2152 R2195
L2016
LX-P1010ZU/ZE
3.3. HOW TO READ THE ADJUSTMENT
PROCEDURES
TP3505
TP3501
Fig. 3-3-1
TP3502
TP3503
Fig. 3-3-2
3.4. ADJUSTMENT PROCEDURES
Preparation for Adjustments 3.4.1. through 3.4.4.
1. Connect a jumper wire between TP2017 and TP2018 on Main
PWB for over 5 seconds to set to the "FACTORY ADJUST"
mode.
2. Press the POWER button on remote control once.
3. While "Please press POWER button again to power off." is
displayed, press the MENU on remote control button.
4. Press 5 or ∞ button to select "VIDEO/RGB ADJUST" mode,
and press ENTER button to set to "VIDEO/RGB ADJUST"
mode.
(PA014) 14
15 (PA014)
Fig. 3-4-1
* Test Patter n Signal
Software Select Menu
Fig. 3-4-2
i s a l s o i n c l u d e d
(installed).
Fig. 3-4-3
5. After completing adjustments 3.4.1. through 3.4.4., press the
"MENU" button to release from "VIDEO/RGB ADJUST" mode.
(Adjustment data is memorized in EEPROM IC (IC2006) by
pressing "MENU" button.) Otherwise, adjustment data 3.4.1.
through 3.4.4. will be cancelled.
Preparation for Adjustments 3.4.5. through 3.4.8., 3.4.11. and
3.4.12.
1. Connect a jumper wire between TP2017 and TP2018 on Main
PWB for over 5 seconds to set to the "FACTORY ADJUST"
mode.
2. Press the POWER button on remote control once.
3. While "Please press POWER button again to power off." is
displayed, press the MENU button.
4. Press 5 or ∞ button on remote control to select "LCD/FAN
ADJUST" mode, and press ENTER buttonto set to "LCD/FAN
ADJUST" mode.
Fig. 3-4-4
Advertisement
Table of Contents
