Integra DTR-7.3 Instruction Manual page 19

Connecting to Audio/Video equipment
8. Settop box, video camera
(VIDEO 3)
S Video output
Video output
L (white)
Analog audio
output
R (red)
Digital audio output (optical)
8, 9. Connecting a satellite tuner, television, or settop box
(VIDEO 3 or 4)
Using an RCA video cable, connect the video output jack
(composite) of the device to the VIDEO 3 (or 4) VIDEO IN jack of
the DTR-7.3. Or if the device has an S video output jack, connect it
to the VIDEO 3 (or 4) S VIDEO IN jack of the DTR-7.3 using an S
video cable. Or if the device has component video outputs, connect
them to one of the banks of COMPONENT VIDEO INPUT jacks on
the DTR-7.3.
With the initial settings of the DTR-7.3, the VIDEO 3 and 4 input
sources are set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at Setup Menu → Input Setup → Video
Setup → Component Video (see page 48).
Using an RCA audio cable, connect the audio output jack of the
device to the VIDEO 3 (or 4) AUDIO IN jacks of the DTR-7.3.
Make sure that you properly connect the left channel to the L jack
and the right channel to the R jack.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAX jack or DIGITAL INPUT OPT jack of the DTR-7.3
depending on the type of connector on the device.
With the initial settings of the DTR-7.3, the VIDEO 3 input
source is set for digital input at the OPT 3 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page 46).
With the initial settings of the DTR-7.3, the VIDEO 4 input source is
not set for digital input. If you are connecting a digital component,
these settings must be changed at Setup Menu → Input Setup →
Digital Setup (see page 46).
DIGITAL PRE
AUDIO VIDEO
INPUT NNA R
COAX
MONITOR
1
R L
SUB
AM
2 OUT ZONE 2
SURR
3 IN
SURR
R
BACK/
OPT
ZONE 2
FM
OUT
1
75
VIDEO 1
FRONT
IN
2
O
R
L
SUB
3 PHONO OUT
VIDEO 2
SURR
CD IN
DIGITAL
OUTPUT
R
OUT
VIDEO 3
OPT IN
SURR
BACK
TAPE
IN VIDEO 4
IN
GND
L R L
O AUDIO VIDEO
10. Connecting video camera, etc. (VIDEO 5 INPUT)
Using an RCA video cable, connect the video output jack
(composite) of the device to the VIDEO 5 VIDEO jack of the DTR-
7.3. Or if the device has an S video output jack, connect it to the
VIDEO 5 S VIDEO jack of the DTR-7.3 using an S video cable.
Using an RCA audio cable, connect the audio output jack of the
device to the VIDEO 5 AUDIO jacks of the DTR-7.3. Make sure that
you properly connect the left channel to the L jack and the right
channel to the R jack.
If the device has an optical digital output, connect it to the VIDEO 5
DIGITAL jack of the DTR-7.3.
The VIDEO 5 digital input is fixed to the OPTICAL input on the
front panel.
COMPONENT
S VIDEO
VIDEO
OUTPUT
OUT
Y
P
B
DVD P
R
INPUT 1
Y
ETHERNET
[NET-TUNE]
CE
P
B
SP
CAUTION:
SPEAKER
IMPEDANCE
P
R
4 OHMS MIN. OR
6 OHMS MIN.
INPUT 2
/SPEAKER
Y
SEE INSTRUCTION
MANUAL FOR
CORRECT SETTING
P
B
P
R
L (white)
S VIDEO
R (red)
S Video output
Digital output
(optical)
10. Video camera/ Video game
(VIDEO 5 INPUT)
Video output
L
Analog output
R
: Signal flow
9. Satellite tuner or television
(VIDEO 4)
S Video output
Video output
Analog audio
output
Front panel
19