Integra DTR-7.3 Instruction Manual page 17

Connecting to Audio/Video equipment
: Signal flow
S Video input
Video input
L (white)
Analog audio
input
R (red)
6. VCR (VIDEO 1)
R (red)
Analog audio
output
L (white)
Video output
S Video output
5. Connecting a television monitor or projector (MONITOR
OUT)
The DTR-7.3 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
Using an RCA video cable, connect the video input jack (composite)
of the device to the MONITOR OUT VIDEO jack of the DTR-7.3.
Or if the device has an S video input jack, connect it to the
MONITOR OUT S VIDEO jack of the DTR-7.3 using an S video
cable. Or if the device has component video inputs, connect them to
the bank of COMPONENT VIDEO OUTPUT jacks on the DTR-7.3.
Note:
Note that the Setup Menu will only be displayed on the monitor
connected to MONITOR OUT (VIDEO and S VIDEO) and not
those connected to the COMPONENT VIDEO OUT PUT jacks.
DIGITAL
PRE
AUDIO VIDEO
INPUT NNA R
COAX FRONT
MONITOR
1
R L
SUB
AM
2 OUT ZONE 2
SURR
3 IN
SURR
R
BACK/
OPT
ZONE 2
FM
1 OUT
75
VIDEO 1
FRONT
2 IN
IO
R
L
SUB
PHONO OUT
3
VIDEO 2
SURR
CD IN
DIGITAL
OUTPUT
R
OUT
IN VIDEO 3
OPT
SURR
BACK
TAPE
VIDEO 4
IN
IN
GND
L R L
IO AUDIO VIDEO
6. Connecting a video cassette recorder (VIDEO 1)
Using RCA video cables, connect the video output jack (composite)
of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the
DTR-7.3 and connect the video input jack of the video cassette
recorder to the VIDEO 1 VIDEO OUT jack of the DTR-7.3. Or if the
video cassette recorder has S video input and output jacks, connect
them to the VIDEO 1 S VIDEO IN and OUT jacks of the DTR-7.3
using S video cables. Or if the video cassette recorder has component
video outputs, connect them to one of the banks of COMPONENT
VIDEO INPUT jacks on the DTR-7.3.
With the initial settings of the DTR-7.3, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the video cassette recorder to the COMPONENT
VIDEO INPUT 1 jacks, this must be changed at Setup Menu →
Input Setup → Video Setup → Component Video (see page 48).
Using RCA audio cable, connect the audio output jacks of the video
cassette recorder to the VIDEO 1 AUDIO IN jacks of the DTR-7.3
and connect the audio input jacks of the video cassette recorder to the
VIDEO 1 AUDIO OUT jacks of the DTR-7.3. Make sure that you
properly connect the left channels to the L jacks and the right
channels to the R jacks.
If you are connecting a digital output device to the VIDEO 1 jack
instead of a VCR, connect it to either the DIGITAL INPUT COAX
jack or DIGITAL INPUT OPT jack depending on the type of
connector on the device.
With the initial settings of the DTR-7.3, the VIDEO 1 input
source is set for digital input at the COAX 2 jack.
If the digital connection is made at a different jack, this must be
changed at Setup Menu → Input Setup → Digital Setup (see page
46).
Video input
S Video input
COMPONENT
S VIDEO
VIDEO
OUTPUT
OUT Y
Y
P
P B
B
P
DVD P
R R
INPUT 1
Y
ETHERNET
[NET-TUNE]
C
P
B
S
CAUTION:
SPEAKER
IMPEDANCE
P
R
4 OHMS MIN. OR
6 OHMS MIN.
INPUT 2
/SPEAKER
Y
SEE INSTRUCTION
MANUAL FOR
CORRECT SETTING
P
B
P
R
S VIDEO
5. TV monitor or projector
(MONITOR OUT)
Component video input
17