Recommended Maintenance; Lubrication; Routine Inspection; Replacing The Sanding Disc - Delta 31-140 Operating Instructions And Parts Manual

NOTE: Disconnect machine from power source before
performing any maintenance.

LUBRICATION

All bearings are sealed and permanently lubricated. No
further lubrication is needed.

ROUTINE INSPECTION

It is recommended that you periodically inspect your
spindle sander as a precautionary action. During this
time, check for the following:
• Inspect all hardware, fittings and fasteners that may
have loosened due to vibration and re-tighten as
needed.
• Check for dust and/or wood particles that may have
accumulated on or in the machine. Check all dust
collection fittings – re-tighten as needed.
• Inspect the ON/OFF SWITCH for damage before each
use. Periodically inspect the power cord and plug for
damage. If necessary replace the power cord and the
plug at the first signs of visible damage.
A complete line of accessories is available from your DELTA
DELTA Factory Service Centers, and DELTA
®
DeltaMachinery.com for an online catalog or for the name or your nearest supplier.
Since accessories other than those offered by dELTA
use of such accessories could be hazardous. For safest operation, only dELTA
accessories should be used with this product.
To register your tool for warranty service visit our website at www.DeltaMachinery.com.
dELTA will repair or replace, at its expense and at its option, any new dELTA
®
use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a dELTA
center or authorized service station with proof of purchase of the product within five years and provides dELTA
to verify the alleged defect by inspection. For all refurbished dELTA
for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone
other than an authorized dELTA
damages resulting from defective products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty is dELTA
with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are
expressly disclaimed by dELTA
1-800-223-7278. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in the packaging, call the local company or see website for warranty
information.

RECOMMENdEd MAINTENANCE

ACCESSORIES

Authorized Service Centers. Please visit our Web Site www.
®

wARRANTY

Five Year Limited New Product warranty
service facility or representative. Under no circumstances will dELTA
®
. For further detail of warranty coverage and warranty repair information, visit www.deltaMachinery.com or call
®

REPLACINg THE SANdINg dISC

M a k e
disconnected from power source.
• To remove sanding disc (A), simply peel old abrasive
disc from machine as shown.
• To install a new abrasive disc, make sure the disc
plate (B) is clean, dry, and free from any oil, grease, or
old adhesive.
• Peel back half the adhesive backing from the new
disc and slide between the table and disc plate so
that the half without the backing is aligned with the
top half of the disc plate.
• Press top half of sanding disc onto top half of disc
plate.
• Manually rotate disc plate one-half turn, remove
remainder of adhesive backing and firmly press
sanding disc onto disc plate.
Make certain the sanding disc is
securely in position before connecting
machine to a power source.
Supplier, DELTA
®
have not been tested with this product,
®
machine, machine part, or machine accessory which in normal
®
product, the warranty period is 180 days. dELTA
®
's sole warranty and sets forth the customer's exclusive remedy,
®
12
c e r t a i n m a c h i n e
Factory Service Centers, and
®
recommended
®
factory service
®
with reasonable opportunity
®
will not be responsible
®
be liable for incidental or consequential
®
i s