Constructing The Appliance Chase; Clearances - Heat & Glo SL-750TRS-IPI-E Owner's Manual

B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling fi restops and wall shield
fi restops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
Chases should be constructed in the manner of all out-
side walls of the home to prevent cold air drafting prob-
lems. The chase should not break the outside building
envelope in any manner.
Walls, ceiling, base plate and cantilever fl oor of the chase
should be insulated. Vapor and air infi ltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infi ltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
To further prevent drafts, the wall shield and ceiling
fi restops should be caulked with caulk with a minimum
B
D
DVP Pipe SLP Pipe
Models
Rough
Opening
(Width)
10
in.
SL-750TRS-IPI-E
SL-750TRS-E
254
mm
10
in.
SL-550TRS-IPI-E
SL-550TRS-E
254
mm
10
in.
SL-350TRS-IPI
254
mm
* Adjust framing dimensions for interior sheathing (such as sheetrock)
C** Add 12 inches when rear venting with one 90º elbow.
Figure 5.2 Clearances to Combustibles
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-IPI • 2120-901 Rev. U • 11/13
A
C
*
MINIMUM FRAMING DIMENSIONS
A B C
**DVP Pipe SLP Pipe
Rough
Rough Rough
Opening
Opening Opening
(Height)
(Width) (Depth)
8-5/8 38-1/4 16-1/4
219 971 413
8-5/8 34-3/4 16-1/4
219 882 413
8-5/8 32-3/4 16-1/4
219 832 413
of 300ºF continuous exposure rating to seal gaps. Gas
line holes and other openings should be caulked with
caulk with a minimum of 300ºF continuous exposure rating
or stuffed with unfaced insulation. If the appliance is be-
ing installed on a cement surface, a layer of plywood may
be placed underneath to prevent conducting cold up into
the room.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
WARNING! Risk of Fire! Maintain specifi ed air space
clearances to appliance and vent pipe:
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fi replace or chimney.
• Failure to maintain airspace may cause overheating and
a fi re.
F
J
D E
Rough
Clearance Combustible
Rough
Opening
to Ceiling
Opening
(Width)
(Depth)
16-1/4 42 32
413 1067 813
16-1/4 37 32
413 940 813
16-1/4 34 32
413 864 813
MEASURE FROM TOP
OF UNIT OPENING
OR FROM TOP OF HOOD
G
I
F G H
Combustible Behind
Floor Flooring Appliance
0 0 1/2
0 0 13
0 0 1/2
0 0 13
0 0 1/2
0 0 13
E
H
I J
Sides of Front of
Appliance Appliance
1/2 36
13 915
1/2 36
13 915
1/2 36
13 915
21