Selecting The Video Format; Setting The Video Signal; Setting The Steering Wheel Control - Pioneer AVH-X4690DVD Owner's Manual

Section
18 System settings
6 Touch Auto EQ Measurement to enter
auto EQ measurement mode.
7 Plug the microphone into the micro-
phone input jack on this unit.
AVH-X5690BTand AVH-X4690DVD
AVH-X2690BTand AVH-X1690DVD
Microphone
Extension Cable
(sold separately)
AUX input
(AUX)
8 Touch Start to start auto EQ.
9 When the 10-second countdown starts,
get out of the car and close the door within
10 seconds.
A measurement tone (noise) is emitted from the
speakers, and auto EQ measurement begins.
When auto EQ is completed, The measurement
has finished. Please disconnect the micro-
phone and then push HOME key. is displayed.
When the car's interior acoustic characteristics
cannot be measured correctly, an error message
will be displayed. (Refer to Understanding auto
EQ error messages on page 53.)
38
En
# It takes about nine minutes for auto EQ measure-
ment to be completed when all the speakers are con-
nected.
# To stop auto EQ, touch Stop.
10 Store the microphone carefully in the
glove compartment or another safe place.
If the microphone is subjected to direct sunlight
for an extended period, high temperatures may
cause distortion, color change or malfunction.

Selecting the video format

You can switch the video output format of V
OUT between NTSC and PAL.
1 Press the home button to switch to the
home display.
2 Touch the system key to open the system
menu.
3 Touch Video Output Format on the sys-
tem menu to select the video output format.
NTSC—PAL
Note
You can switch the video output format only for
the source from this unit.

Setting the video signal

When you connect this unit to an AV equipment
to this unit, select the suitable video signal set-
ting.
! As this function is initially set to Auto, the
unit will automatically adjust the video signal
setting.
! You can operate this function only for the
video signal input into the AV input.
1 Press the home button to switch to the
home display.
System settings
2 Touch the system key to open the system
menu.
3 Touch Video Signal Setting on the system
menu.
Video Signal Setting items are displayed.
! AV – Adjusts the AV video signal
! AUX – Adjusts the AUX video signal
! Camera – Adjusts the rear view camera video
signal
4 Touch c or d to select the desired video
signal appears.
Auto—PAL—NTSC—PAL-M—PAL-N—SECAM
Setting the steering wheel
control
You can set the steering wheel control on the
unit's display via a wired remote cable. Refer to
Connecting the power cord on page 44.
This setting is required in order to use the steer-
ing wheel remote control function.
Important
! In some cases this function may not work
correctly.
For details please contact your dealer or an
authorized Pioneer Service Station.
! Park your car in a safe place and use this
function. Do not operate it while driving.
1 Press the home button to switch to the
home display.
2 Touch the system key to open the system
menu.
3 Touch Steering Wheel Control on the sys-
tem menu.
The Steering Wheel Control screen appears.
Steering Wheel Control
This function allows you to control this In-Dash
Receiver from your steering wheel control.
If you have a connected steering wheel control adapter
for Pioneer, please choose "With Adapter". If you are
connected to your steering wheel control directly,
please choose "Without Adapter".
With Adapter Without Adapter
1 2
1 With Adapter key
Touch this key when connecting a steering
wheel control adapter for Pioneer.
2 Without Adapter key
Touch this key when directly connecting to
the car's steering wheel control harness.
4 Select settings according to the connec-
tion method being used.
# For steering wheel control adapter for
Pioneer users
1 Touch With Adapter.
Follow the on-screen instructions for subse-
quent steps.
# For users directly connecting the unit to the
car's steering wheel control harness
1 Touch Without Adapter.
Proceed to the next step to continue.
5 Touch Clear.
The confirmation screen appears.
When it is unnecessary to clear the settings,
such as when changing key assignment, pro-
ceed to step 7.
6 Touch OK.
You must clear all default settings before you
use this function.