Related Manuals for LevelOne FCS-3054
Summary of Contents for LevelOne FCS-3054
- Page 1 Fixed Network Camera Hardware User Manual FCS-3054, FCS-3065, FCS-3092 Ver. 2014/01/09...
-
Page 2: Table Of Contents
Hardware Manual Table of Contents Precautions Safety Instructions ................5 Introduction List of Models ..................6 Package Contents ................7 Physical Description ................ 8 Installation Procedures Installing the Camera on a Surface ..........11 Basic Connections ................. 14 Other Adjustments and Accessories How to Adjust the Viewing Angle and Focus ....... -
Page 3: Precautions
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment. - Page 4 Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 5: Safety Instructions
Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like. -
Page 6: Introduction
Hardware Manual Introduction List of Models This hardware manual contains the following models: FCS-3054 3MP Indoor Mini Dome with Fixed lens FCS-3065 5MP Indoor Mini Dome with Basic WDR, Fixed lens FCS-3092 5MP Indoor Mini Fisheye Dome with Basic WDR, Fixed lens From the installation perspective, these camera models are very similar, therefore one manual can be used for all of them. -
Page 7: Package Contents
Hardware Manual Package Contents Camera Camera FCS-3092 (Mini Fisheye Dome) Drill Template Screw Kit Drill Template Lens Focus Tuner Hexagon Screwdriver (Not available in E93, E96, and E97 models) Quick Installation Guide... -
Page 8: Physical Description
Hardware Manual Physical Description Mini Dome Mini Fisheye Dome... - Page 9 Hardware Manual 1) Ethernet Port The Ethernet port connects to a network using an Ethernet cable. 2) Reset Button The Reset Button is used to restore the factory default settings of the camera, including the administrator’s password. How to reset the camera? While the power is on, press and hold the Reset Button for 5 seconds or until the Blue LED lights up.
-
Page 10: Installation Procedures
Hardware Manual Installation Procedures Before mounting the camera, remove the dome cover by loosening the three (3) screws. There are two ways to mount the camera: Surface mount: Use this method to mount the camera directly on the ceiling. See Installing the Camera on a Surface on page 11. -
Page 11: Installing The Camera On A Surface
Hardware Manual Installing the Camera on a Surface 1. Mark the location of the screw holes base on the drill template included in the package. Conduit Hole NOTE: Depending on the surface where you will install the camera, it may be necessary to drill three (3) holes with φ... - Page 12 Hardware Manual 3. Use the camera body and locate the three (3) screw holes. 4. Install the camera body to the ceiling using the three (3) screws included in the camera package. NOTE: Please make sure the screw is flat on the plate.
- Page 13 Hardware Manual 5. Connect the Ethernet cable to the Ethernet port of the camera. 6. Adjust the camera viewing angle and focus. See How to Adjust the Viewing Angle Focus on page 15. NOTE: Not applicable to E96 model. 7. Attach the cover to the camera body and tighten the three (3) screws to secure it.
-
Page 14: Basic Connections
Hardware Manual Basic Connections Follow the procedures below to connect the camera to the network. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector using an Ethernet cable. 2) Connect your PoE Switch / Injector to a PC / network using another Ethernet cable. -
Page 15: Other Adjustments And Accessories
Hardware Manual Other Adjustments and Accessories How to Adjust the Viewing Angle and Focus NOTE: The following procedures are not applicable toFCS-3092 (Mini Fisheye Dome) cameras. 1. Loosen the three (3) screws to remove the dome cover. 2. Based on the live view from the camera, adjust the viewing angle with pan and tilt direction (for Mini Dome models only). - Page 16 Hardware Manual 3. Adjust the focus. NOTE: Not applicable for FCS-3065 model because the camera is already pre-focused. a. Attach the focus tuner (included in the camera package) on the lens and adjust the focus of the lens. b. Remove the lens focus tuner. 4.
-
Page 17: How To Replace The Dome Cover
Hardware Manual How to Replace the Dome Cover For more discrete surveillance needs, the pre-installed dome cover can be replaced with a smoked, non-vandal proof dome cover. The smoked dome cover is an optional accessory; contact your sales agent to purchase. To replace the dome cover, follow the procedures below: 1. - Page 18 Hardware Manual 3. Remove the ring from the cover. 4. Insert ring to the new dome cover and latch it to the cover body.
-
Page 19: How To Replace The Lens (For Fcs-3065 Only)
Hardware Manual How to Replace the Lens (for FCS-3065 only) For wider viewing angle, the bundled lens can be replaced with the optional IR-compatible lens. Contact your sales agent to purchase. To replace the lens, follow the procedures below: 1. Using the bundled hex screwdriver, loosen the three (3) screws to open the dome cover. 2. - Page 20 Hardware Manual 3. When the lens comes off, remove the spring and remove the bundled lens from the lens focus tuner. 4. Remove the transparent plastic from the replacement lens. 5. Attach the spring to the replacement lens. 6. Continuously rotate the replacement lens to attach it to the camera.
- Page 21 Hardware Manual 7. Attach the lens focus tuner when the tip of the lens is difficult to hold then turn it clockwise or counter-clockwise to adjust the camera focus. See How to Adjust the Viewing Angle and Focus on page 15 for more information. 8.
-
Page 22: Accessing The Camera
Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from each other. - Page 23 Hardware Manual By double-clicking with the left mouse on the camera model, it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network –...
-
Page 24: Using The Default Camera Ip Address
Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100... -
Page 25: Access The Camera
Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices –... - Page 26 Hardware Manual You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft Internet Explorer. The browser functionality comparison: Functionality Internet Explorer Other browsers Live Video Live Video Area Resizable PTZ Control Capture the snapshot Video overlay based configuration (Motion Detection regions, Privacy Mask regions)
- Page 27 Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera. Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page.
- Page 28 Hardware Manual To check the firmware version through the Web Configurator, access the Setup page and click System > System Info. For further operations, please refer to the Firmware User Manual.