Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LevelOne FCS-3053
Summary of Contents for LevelOne FCS-3053
- Page 1 Fixed Dome Network Camera Hardware User Manual FCS-3053, FCS-3063 Ver. 2014/01/16...
-
Page 2: Table Of Contents
Introduction List of Models ....................6 Package Contents ..................6 Physical Description ................. 7 FCS-3053 / FCS-3063 ..............7 Installing the Camera on a Surface Step 1: Unpack the Camera ..............8 Step 2: Attach the Mounting Plate ............9 Step 3: Connect the Cable .............. - Page 3 Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
- Page 4 Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 5: Safety Instructions
Hardware Manual Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like. -
Page 6: Introduction
Hardware Manual Introduction List of Models This hardware manual contains the following models: Fixed Dome Network Camera, 3-Megapixel, PoE 802.3af, Day & Night, FCS-3053 IR LEDs Fixed Dome Network Camera, 5-Megapixel, PoE 802.3af, Day & Night, FCS-3063 , WDR IR LEDs From the installation perspective, these models are similar;... -
Page 7: Physical Description
Hardware Manual Physical Description FCS-3053 / FCS-3063 1) Ethernet Port Connects to the network using a standard Ethernet cable (CAT5 / CAT6). 2) Reset Button Restores the camera factory default settings. To do the reset, press and hold the Reset Button... -
Page 8: Installing The Camera On A Surface
Hardware Manual Installing the Camera on a Surface This section describes the procedures in installing the camera directly on a flat surface, such as the ceiling or the wall. For simplicity, most of the camera images used in the succeeding sections were taken using the camera model with heat sink;... -
Page 9: Step 2: Attach The Mounting Plate
Hardware Manual Step 2: Attach the Mounting Plate NOTE: Before installation, consider the camera viewing angle and logo placement. The arrow on the drill template and mounting plate align with the direction of the camera logo. Rotate the drill template as needed. 1. -
Page 10: Step 3: Connect The Cable
2. Connect the network cable to the Ethernet port of the camera. Step 4: Attach the Fixing Bracket This step is required only for FCS-3053, FCS-3063 camera models with cables going along the surface. Otherwise, skip this step. 1. Route the cable to pass through the gap on the camera. - Page 11 Hardware Manual 2. Attach the fixing bracket using the two (2) supplied screws to secure the cable.
-
Page 12: Step 5: Install The Camera
Hardware Manual Step 5: Install the Camera 1. If the cable passes through a hole on the surface, push the extra length of cable into the hole. Otherwise, skip this step. 2. With the arrow on the mounting plate aligned to the direction of the camera logo, insert the hooks on the camera to the slots on the mounting plate. -
Page 13: Step 6: Connect To Network
Hardware Manual Step 6: Connect to Network Connect the other end of the network cable to a Power-over-Ethernet (PoE) switch or injector. Then, connect the PoE switch or injector to a network or PC and a power source. See example connection diagram below. -
Page 14: Step 9: Close The Dome Cover
Hardware Manual Step 9: Close the Dome Cover 1. Slightly press on the edges of the dome cover and push it into the groove until it clicks. 2. Remove the plastic covering the dome cover. Below is an installation example. -
Page 15: Other Adjustments And Accessories
Other Adjustments and Accessories How to Adjust the Viewing Angle and Focus This section describes the procedures in adjusting the viewing angle and focus of the camera. FCS-3053 / FCS-3063 Camera Parts Overview Adjustment Procedures 1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to fix the tilt position. -
Page 16: How To Replace The Dome Cover
Hardware Manual How to Replace the Dome Cover For more discrete surveillance needs, the bundled dome cover can be replaced with a smoke dome cover available for purchase. To replace the dome cover, do the following: 1. Rotate the current dome cover counter-clockwise and then pull to remove it. 2. - Page 17 Hardware Manual 4. Remove the plastic covering the dome cover.
-
Page 18: Accessing The Camera
Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from each other. - Page 19 Hardware Manual By double-clicking with the left mouse on the camera model, it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network –...
-
Page 20: Using The Default Camera Ip Address
Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100... - Page 21 Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices –...
-
Page 22: Access The Camera
Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft Internet Explorer. - Page 23 Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera. Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page.
- Page 24 Hardware Manual To check the firmware version through the Web Configurator, access the Setup page and click System > System Info. For further operations, please refer to the Firmware User Manual.