Basic Operations - JVC RX-DVSSL Instructions Manual

I
Basic Operatio
On the front panel From the remote control
Press O/I STANDBY/ON on the front panel or
W STANDBY/ON AUDIO on the remote control.
The STANDBY lamp goes off and the illumination lamp lights up.
The current source name appears on the display.
l
If the built-in DVD player is the current source, "READING"
appears while the unit is detecting the type of the loaded disc
(see page 29).
- Playback starts automatically when you load some DVD
VIDEO.
- "NO DISC" appears on the display when no disc is loaded.
To turn off the power (into standby)
Press O/I STANDBY/ON on the front panel or
o/I STANDBY/ON AUDIO on the remote control again.
The illumination lamp goes off and the
O/I
STANDBY lamp lights up.
a 0 SlA~DBY
STANDBYION
Note:
v
l
A
small amount of the power is consumed even in standby mode.
To turn off the power complete/H unplug the AC power cord.
On the front panel
&BmPEB
DBS VCR D"D
000
From the remote control
Press one of the source selecting buttons.
DVD
DBS*
VCR
TV*
TAPE/CDR*
TAPE
Select the cassette deck (remote control ONLY *"6).
CDR"
Select the CD recorder (remote control ONLY:+z:).
FM/AM
Select an FM or AM broadcast.
Select the built-in DVD player.
Select the DBS tuner.
Select the VCR.
Select the TV tuner.
Select the cassette deck or the CD recorder
(front
panel ONLY)
When you press one of the buttons listed above, the remote
control
operation mode appears on the operation mode display for about 2
hours.
ci_nq
Ex. : When you press DVD
Notes:
'. Register the digital input terminal setting (see "Digital Input
(DIGITAL IN) terminals"on page 21) and digital input mode setting
correct/y (see 'Selecting the Analog or Digital Input Mode" on page
13). Source name and "DIGITAL" will be shown on the display when
you select the source.
~'? When the source name is not assigned correct/v, these buttons
cannot work (see "Changing the Source Name"on page 12).
On the front oanel:
To increase the volume,
turn MASTER VOLUME clockwise.
To decrease the volume,
turn MASTER VOLUME counterclockwise.
From the remote control:
To increase the volume,
press and hold VOLUME +.
To decrease the volume,
press and hold VOLUME -.
CAUTION:
Always set the volume to the mlnimum before starting any sources. If
the volume is set at a high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Notes:
l
The volume level can be adjusted within the range of '0" (minimum)
to '50" (maximum).
l
When DVD is selected as the source with your TV turned on, the
volume /eve/ indication appears on the TV
Listening with headphones
Connect a pair of headphones to the (3 (phones) jack on the
front panel. This cancels the Surround mode currently
@
selected, deactivates speakers. and activates the
4,
HEADPHONE mode.
The
SPK. indicator
goes off t'rom the display.
* Disconnecting a pair of headphones from the i) (phones)
jack
cancels the HEADPHONE mode and activates speakers
HEADPHONE mode
When using the headphone\. the following signals are output
regardless of your speaker \etting:
~~~ For Z-channel sources. the front left and right
channel signal5
are output directly from the left and right hcadphoncs.
~ For multichannel sources. the front left and right, center and
rear channel
signals are down-mixed and then output f.rom the
headphones without missing bass clement.
-For DVD AUDIO ONLY: When
the multichannel track
cannot be down-mixed. only signal\ of the firont left and right
channel are output.
CAUTION:
Be sure to turn down the volume:
l
Before connecting or putting on headphones, as high volume can
damage both the headphones and your hearing.
l
Before removing headphones, as high volume may output from the
speakers.
11