Directed Electronics Valet 561T Installation Manual page 34

■ T T h h e e r r e e m m o o t t e e s s t t a a r r t t w w i i l l l l a a c c t t i i v v a a t t e e b b u u t t t t h h e e s s t t a a r r t t e e r r n n e e v v e e r r e e n n g g a a g g e e s s . .
1. Check for voltage on the purple starter wire two seconds after the remote start becomes active. If there is
voltage present, skip to Step 4. If there is not voltage present, advance to Step 2.
2. Check the 30A fuses.
3. Check diagnostics. If the gray/black wire is detecting ground upon activation, the starter will not crank.
4. Make sure the purple starter wire is connected on the starter side of the optional starter kill relay.
5. Does the vehicle have an immobilizer? Some immobilizer systems will not allow the vehicle to crank if active.
6. Check connections. The two red heavy gauge input wires on the relay satellite should have solid connec-
tions. "T-taps", or "scotch locks" are not recommended for any high current heavy gauge wiring. Also, if the
vehicle has more than one 12-volt input wire, then connect one red wire to each.
■ T T h h e e v v e e h h i i c c l l e e s s t t a a r r t t s s , , b b u u t t i i m m m m e e d d i i a a t t e e l l y y d d i i e e s s . .
1. Does the vehicle have an immobilizer? The vehicle's immobilizer will cut the fuel and/or spark during unau-
thorized starting attempts.
2. Is the remote start programmed for voltage sense? If so, the start time may not be set high enough, or you
may have to adjust the voltage threshold in programming. Voltage sense will not work on some vehicles.
3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking.
■ T T h h e e v v e e h h i i c c l l e e s s t t a a r r t t s s , , b b u u t t t t h h e e s s t t a a r r t t e e r r k k e e e e p p s s r r u u n n n n i i n n g g . .
1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these
features, the engine cranks for the preprogrammed crank time regardless of how long it takes to start the
vehicle to actually start. Adjust to a lower cranking time.
2. Was the Tach Learn successful? The LED must light solidly and brightly to indicate a successful learn.
3. Make sure that there is a tach signal right at the purple/white tach input wire of the remote start. If not,
recheck the connection to the vehicle's tach wire and make sure the wire is not broken or shorted to ground
leading to the remote start.
■ T T h h e e v v e e h h i i c c l l e e w w i i l l l l s s t t a a r r t t a a n n d d r r u u n n o o n n l l y y f f o o r r a a b b o o u u t t 1 1 0 0 s s e e c c o o n n d d s s . .
1. Is the remote start programmed for voltage sense? Try programming the unit for low voltage reference. If
this does not work, a tach wire should be used.
2. Check diagnostics.
■ D D i i e e s s e e l l v v e e h h i i c c l l e e d d o o e e s s n n o o t t w w a a i i t t t t o o s s t t a a r r t t . .
1. Is the GRAY/BLACK wire connected to the wait-to-start wire of the vehicle?
2. Check the polarity of the wait-to-start wire. (See the Finding the Wait-to-Start Bulb Wire For Diesels section
of this guide.)
3. If wiring a negative wait-to-start bulb, make sure that a diode has been placed in line on the factory wire
between the vehicle's ECM and the wait-to-start bulb. (See wiring description for the H1/6 GRAY/BLACK (-
) Diesel Wait-To-Start Bulb Input of the Primary Harness Wire Connection Guide .)
3 3 4 4
© 2005 Directed Electronics—all rights reserved