Table of Contents
Advertisement
SCANNING
EXPOSURE, RESOLUTION, AND FILE FORMAT)
When sending an image, you can adjust the original size, exposure, resolution, and file format settings as needed.
MANUALLY SETTING THE SCANNING SIZE
If you load an original that is not a standard size (such as an AB size), or if you wish to change the scanning size,
touch the [ORIGINAL] key and set the original size manually.
Perform the following steps after loading the document in the automatic document feeder or on the document glass.
NOTE
Standard sizes that can be detected are as follows:
11"x17", 8-1/2"x14", 8-1/2"x11", 8-1/2"x11"R, 5-1/2"x8-1/2" (A3, B4, A4, A4R, B5, B5R, A5)
If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed, or
the original size may not appear at all.
1
Touch the [ORIGINAL] key.
300 x 300dpi
RESOLUTION
PDF MMR(G4)
FILE FORMAT
AUTO
8½
11
X
ORIGINAL
2
Touch the [SCAN SIZE] key.
SCAN SIZE
SEND SIZE
100%
AUTO
AUTO 8½
11
X
2-SIDED
2-SIDED
BOOKLET
TABLET
NOTE
If you wish to rotate the original 90° when creating an
image file, touch the "ROTATE THE IMAGE 90
DEGREES" checkbox (a checkmark should appear
in the box). (only in the E-MAIL/FTP mode)
3
Touch the desired original size key.
OK
5
1
8
1
8
1
13
X
X
2
2
2
AB
8
1
14
5
1
8 R
1
X
X
2
2
2
INCH
8
1
11
X
11
17
X
2
1
LONG SIZE
8
11R
X
2
STANDARD SIZE
SIZE INPUT
SETTINGS
The sizes that can be
selected are displayed.
[AUTO] is no longer
highlighted. [MANUAL]
and the original size key
you
touched
are
highlighted.
20
(ORIGINAL
If you wish to select an AB size, touch the
[AB] key and then touch the desired
original size key.
OK
A5
A4
AB
A4R
A5R
INCH
B5
B4
B5R
A3
LONG SIZE
STANDARD SIZE
SIZE INPUT
If you wish to select a custom size, touch
the [SIZE INPUT] key and enter the size of
the original
MANUAL
AUTO
(2 1/2 17)
17
X
MANUAL
inch
(2 1/2 11 5/8)
Y
11
inch
CUSTOM
SIZE
STANDARD SIZE
SIZE INPUT
(64 to 432 mm) in the X direction and 2-1/2" to 11-
5/8" (64 to 297 mm) in the Y direction, set in
increments of 1/8" (1 mm).
When using the automatic document
feeder, a setting for originals longer than
17" (432 mm) (31-1/2" (800 mm) at the
maximum) is available. In this case, touch
the [LONG SIZE] key.
OK
8
1
13
5
1
8
1
X
X
2
2
2
AB
1
5
1
8 R
1
8
14
X
X
2
2
2
INCH
8
1
11
X
11
17
X
2
8
1
11R
LONG SIZE
X
2
STANDARD SIZE
SIZE INPUT
SIZE,
[AB] is highlighted and
AB
size
keys
are
displayed.
To return to the inch
palette, touch the [INCH]
key once again.
Touch the [X] key and
use the
or
keys
to set the length in the X
direction, and then touch
the [Y] key and do the
same for the Y direction.
The length can be within
the range 2-1/2" to 17"
Advertisement
Chapters
Table of Contents
