Skoda Fabia Owner's Manual page 16

If you wish to determine the average fuel consumption over a certain period of
time, you must set the memory at the start of the new measurement to zero us-
ing the button » Fig. 6 on page 13. After erasing the memory, no value appears
B
in the display until you have driven approx. 300 m.
The display is updated regularly while you are driving.
Range
The estimated range in kilometres is shown on the display. It indicates the dis-
tance you can still drive with your vehicle based on the level of fuel in the tank
and the same style of driving.
The display is shown in steps of 10 km. Once the fuel gauge pointer reaches the
reserve marking, the range is displayed in 5 km.
The fuel consumption over the last 50 km is used to calculate the range. The
range will increase if you drive in a more economical manner.
If the memory is set to zero (after disconnecting the battery), the fuel consump-
tion of 10 ltr./100 km is calculated for the range; afterwards the value is adapted
accordingly to the style of driving.
Distance travelled
The distance travelled since the memory was last erased is shown in the dis-
play » page 12. If you want to measure the distance travelled from a particular
moment in time on, at this moment, reset the memory by setting the button
» Fig. 6 on page 13 to zero.
B
The maximum distance indicated in both memories is 1 999 km or 9 999 km on
vehicles with an information display. The indicator is set back to zero if this period
is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display
in km/hour » page 12. To determine the average speed over a certain period of
time, set the memory to zero at the start of the measurement using button
» Fig. 6 on page 13.
B
After erasing the memory, no value appears in the display until you have driven
approx. 300 m.
The display is updated regularly while you are driving.
Current speed
The current speed which is identical to the display of the speedometer
on page 8 is indicated on the display.
14
Using the system
Oil temperature
If the oil temperature is lower than 50 °C or if a fault in the system for checking
the oil temperature is present, only - -.- is displayed instead of the oil tempera-
ture.
Warning against excessive speeds
ä
First read and observe the introductory information and safety warn-
ings on page 12.
Adjust the speed limit while the vehicle is stationary
›
With button A » Fig. 6
cessive speeds.
›
Press the button
›
Use the button
A
›
Confirm the speed limit that was set with button
until the setting is saved automatically (the value stops flashing).
This allows you to set the speed in 5 km/h intervals.
Adjusting the speed limit while the vehicle is moving
›
With button » Fig. 6
A
cessive speeds.
›
Drive at the desired speed, e.g. 50 km/h.
›
Press button to accept the current speed as the speed limit (the value flash-
B
es).
If you wish to change the set speed limit, it is changed in 5 km/h intervals (e.g. the
accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).
›
Confirm the speed limit that was set by pressing button
prox. 5 seconds until the setting is saved automatically (the value stops flash-
ing).
Change or delete speed limit
›
With button » Fig. 6
A
cessive speeds.
›
Pressing the button
›
Pressing the button
If the set speed limit is exceeded, an audible signal will sound as a warning. At
the same time the message Warning against excessive speeds appears on the
» Fig. 2
3
display with the set limit value.
The set speed limit value remains stored even after switching off the ignition.
on page 13, choose the menu point Warning against ex-
to activate the ability to set the speed limit (value flashes).
B
to set the required speed limit, e.g. 50 km/h.
, or wait approx. 5 seconds
B
on page 13, choose the menu point Warning against ex-
on page 13, choose the menu point Warning against ex-
deletes the speed limit.
B
activates the ability to change the speed limit.
B
Ð
again, or wait ap-
B
Ð