Table of Contents
Advertisement
assembling the blades
Hunter fans use several styles of fan blade irons (brackets that hold
the blade to the fan).
1.
Your fan may include blade grommets. If your fan has grom-
mets, insert them by hand into the holes on the blades as shown
in Figure 18.
F F F F F i i i i i g g g g g ur ur ur ur ure 18 - I
e 18 - I
e 18 - In n n n n s s s s s e e e e e r r r r r t t t t t in in in in ing t
e 18 - I
e 18 - I
g t
g t
g t
g th h h h h e g
e gr r r r r o o o o o mm
e g
e g
e g
2.
Attach each blade to blade iron using three blade assembly
screws as shown in Figure 19. Some fans feature a decorative
medallion as well as a blade iron. Insert the assembly screws
into the blade iron, through the blade and into the medallion,
with the blade sandwiched between the blade iron and me-
dallion as shown in Figure 20.
F F F F F i i i i i g g g g g ur ur ur ur ure 19 - A
e 19 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t
e 19 - A
e 19 - A
e 19 - A
g t g t
g t
g th h h h h e b
© 2002 Hunter Fan Company
Grommet
Fan Blade
mme e e e e t t t t t s in
mm
mm
mm
s in
s in
s int t t t t o t
s in
o t
o t
o t
o th h h h h e f e f e f e f e fa a a a a n b
n bl l l l l a a a a a d d d d d e e e e e s s s s s
n b
n b
n b
e b
e b
e bl l l l l a a a a a d d d d d e t
e b
e t e t
e t
e to t
o t
o th h h h h e b
o t
o t
e b
e b
e b
e bl l l l l a a a a a d d d d d e ir
e iro o o o o n n n n n
e ir
e ir
e ir
Blade Iron
Medallion
F F F F F i i i i i g g g g g ur ur ur ur ure 20 - A
e 20 - A
e 20 - A
e 20 - A
e 20 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t
g t
g t g t
g th h h h h e b
m m m m m e e e e e d d d d d a a a a a lli lli lli lli llio o o o o n n n n n
If you used grommets, the blades may appear slightly loose
after screws are tightened. This is normal.
3.
Remove the blade mounting screws and rubber shipping
bumpers from the motor.
4.
For each blade, insert one blade mounting screw through the
blade iron as shown in Figure 21, and attach lightly to the fan.
Insert the second blade mounting screw, then securely tighten
both mounting screws.
F F F F F i i i i i g g g g g ur ur ur ur ure 21 - A
e 21 - A
e 21 - A
e 21 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t
e 21 - A
installing the switch housing
attaching the upper switch housing
1.
Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 22.
2.
Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 22.
Switch Housing
Mounting Plate
Upper Switch
Housing
F F F F F i i i i i g g g g g ur ur ur ur ure 22 - A
e 22 - A
e 22 - A
e 22 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t
e 22 - A
g t
g t
g t
g th h h h h e up
m m m m m o o o o o un
un
unt t t t t in in in in ing p
un
un
e b
e bl l l l l a a a a a d d d d d e t
e b
e b
e t e t
e t
e to t
o t
o th h h h h e b
o t
o t
e b
e b
e b
e bl l l l l a a a a a d d d d d e ir
e ir
e ir
e iro o o o o n a
e ir
n a
n a
n a
n an n n n n d d d d d
g th h h h h e b
g t g t
g t
e b
e b
e bl l l l l a a a a a d d d d d e ir
e iro o o o o n t
e ir
e ir
n t
n to t
n t
o t
o t
o th h h h h e f e f e f e f e fa a a a a n n n n n
e b
e ir
n t
o t
Housing
Assembly
Screw
Upper Plug
Connector
e up
e up
e up
e upp p p p p e e e e e r s r s r s r s r sw w w w w i i i i i t t t t t c c c c c h h
h h
h h
h ho o o o o u u u u u sin
h h
sing t
sin
sin
sin
g t
g t
g t
g to t
o th h h h h e e e e e
o t
o t
o t
g p
g p
g pl l l l l a a a a a t t t t t e e e e e
g p
41844-01 12/20/2002
7 7 7 7 7
Advertisement
Table of Contents
