Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hunter 41895-01
Summary of Contents for Hunter 41895-01
- Page 1 41895-01 • 10/14/05...
-
Page 2: Table Of Contents
• Read this entire manual carefully before beginning installation. Save these instructions. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied. - Page 3 Understanding Mounting Hunter’s patented mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of two ways, depending on your preference: Standard or Angle mounting. e steps in this manual include instructions for both mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
e pilot holes should be 9/64” in diameter. 2-2. Your fan comes with four neoprene noise isolators (“Isolators”). Position the isolators between the ceiling plate and ceiling by inserting the raised areas on each isolator into the holes in the ceiling plate. -
Page 6: Installing The Blade Irons
3-2. For each blade iron, insert one blade iron mounting screw through the blade iron, and partially attach to the fan. Insert the second blade iron mounting screw, and then securely tighten both mounting screws. -
Page 7: Assembling And Hanging The Fan
Once assembled, do not remove the downrod. 4-3. Find the allen head set screw in the adapter on the fan by raising and angling the spindle. Tighten the allen head set screw using the large allen wrench provided. -
Page 8: Setting The Remote Transmitter And Receiver
5-2. Install the included 9-volt battery into the transmitter. CAUTION: e remote control device complies with part 15 of the FCC rules. Changes or modifi cations not expressly approved by Hunter Fan Company could void your authority to operate this equipment. -
Page 9: Wiring The Fan
• e black/white wire from the fan to the red wire from the receiver (marked on white tag “LIGHT OUT”) • e black wire from the fan to the black wire from the receiver (marked on white tag “FAN OUT”) •... -
Page 10: Installing The Canopy And Canopy Trim Ring
Steps 7-4 – 7-5 Hunter Fan Company 7-1. Holding the canopy, raise the fan off the hook. 7-2. Align the slots in the canopy with the tabs on the ceiling plate. 7-3. Raise the canopy over the ceiling plate. Rotate the canopy clockwise until the tabs on the ceiling plate totally engage with the slots in the canopy. -
Page 11: Assembling The Blades
e blades may appear slightly loose after screws are tightened. is is normal. 41895-01 • 10/14/05 8 • Assembling the Blades Step 8-1... -
Page 12: Installing The Glass
9-5. Insert the flathead thumbscrew (from Step 9-1) into the round hole on the top of the light fixture. Tighten it to secure the glass bowl. 9-6. Restore power to the fan. Keyhole Slot Flathead umbscrew Step 9-5 41895-01 • 10/14/05... -
Page 13: Operating The Remote Control And Mounting The Holder
10 • Operating the Remote Control and Mounting the Holder 10-1. e remote has individual buttons for setting fan speed and light intensity. Refer to the figure on the right. Note: For best operation, start the fan by pressing high, then select your desired speed. -
Page 14: Operating And Cleaning Your Ceiling Fan
11-1. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft. -
Page 15: Troubleshooting
1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade and/or blade iron screws. 3. Turn power off , support fan very carefully, and check that the hanger ball is properly seated. 41895-01 • 10/14/05 12 •...