If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to recess the bottom of the outlet box a minimum of 1/16” into the ceiling. 3-2. Check the support brace to ensure it will support the full weight of the fan and light kit.
Page 5
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 41225-01 • 12/04/09 • Hunter Fan Company Isolator Ceiling Plate 3” Wood Screw...
Make certain the housing sits flat on the adapter. 3-2. Install three (3) assembly screws and tighten them securely. 41225-01 • 12/04/09 • Hunter Fan Company Steps 3-1 – 3-2 Top Housing Raised Tabs...
4-1. Unbundle the wires from the fan. For Standard or Angled mounting: 4-2. To assemble fan to hang down from a flat or angled ceiling, insert the downrod through the canopy. Feed the wires from the fan through the downrod.
5-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 41225-01 • 12/04/09 • Hunter Fan Company 5 • Wiring the Fan Wire...
Turn the canopy counterclockwise until it locks into place and will not turn any more. 6-3. Insert and tighten the canopy screws securely. Canopy Screw 41225-01 • 12/04/09 • Hunter Fan Company 6 • Installing the Canopy Step 6-2 Canopy...
3 • Assembling tbe Blades 7 • Assembling the Blades Steps 7-1-7-3 41225-01 • 12/04/09 • Hunter Fan Company 7-1. Insert blade into slot. Align the holes on the blade with the holes in the fan motor. 7-2. Slide blade grommets onto the shafts of the blade assembly screws.
3 • Assembling tbe Blades 8 • Aligning the Fixture Fitter 8-1. Looking up at the bottom of the fan trim. Locate the raised arrow on the bottom of the trim. Before proceeding with the next step make sure you’ve located the arrow.
Page 14
Step 8-6-8-8 Note: In compliance with U.S. Federal energy regulations, this ceiling fan contains a wattage saver that restricts the light kit to a maximum of 190 Watts. Exceeding that limit or the specifications on the light sockets may result in fire hazard or improper operation. If lights do not appear to be operating properly, see the troubleshooting section 41225-01 •...
9-5. Assemble the finial to the bottom of the light fixture by guiding the (2) pull chains and threaded tube through the (3) openings in the finial. 41225-01 • 12/04/09 • Hunter Fan Company Step 9-1 Step 9-2 Clearance Holes...
10 • Operating and Cleaning Your Ceiling Fan 10-1. Turn on electrical power to the fan. 10-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings.
2. Check to see if the blade is cracked. If so, replace all the blades. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws.