Technical Specifications; Appendix; Table: Effects And Effect Parameters - Hughes & Kettner DSM Manual

ZENTERA - MANUAL
®
E2) The zenTera is cabled up and connected properly, but no
sound is audible.
• One or more of the volume knobs or the master knob is/are
turned all the way down. Dial in higher settings.
• The internal speakers are not connected. Plug them in.
®
• The zenTera is in TUNER mode, which means that it is muted.
Quit TUNER mode by tapping the
• A shorted external speaker cable caused one of the internal
fuses to blow. Have a qualified technician change the fuse
(ensure the replacement fuse bears the proper rating).
• The volume pedal of the connected Z-Board is set to the
minimum position. Floor the pedal.
E3) The zenTera ® will not respond to the Z-Board or footswitch.
• The connector of the Z-Board or footswitch is not plugged in
correctly or at all. Plug it into the zenTera
seated firmly.
E4) The sound is totally distorted when you activate a connected
effects device.
• The input of the effect device is being overdriven. If it is
equipped with a level meter or other level indicator, check the
signal level and back off the signal processor's input sensitivity
(via a knob labeled "Input" or "Gain").
E5) The signal level drops considerably when you connect an
external effects device,
• The effect device is sending the signal back at too low a level.
Turn up the signal processor's output level.
E6) A connected MIDI controller is not getting operating voltage
via the phantom power feed of the MIDI IN port:
• The MIDI cable is defective. Replace it with a new cable.
• The phantom power fuse tripped. Replace the blown fuse
making sure that the replacement has the same specs as the
original fuse.

10.0 TECHNICAL SPECIFICATIONS

PREAMP SECTION
INPUT -10 dBV / 1 M ohm
FX RETURN L/R 0 dBV / 10 K ohms
FX SEND L/R 0 dBV / 220 ohms
RECORDING OUT L/R 0 dBV / 220 ohms
POWER AMP SECTION
OUTPUT POWER 2 x 100 watts into 6 ohms
2 x 60 watts into 16 ohms
FREQUENCY RESPONSE 20 Hz - 20 KHz
SPEAKER OUTS Minimum impedance per channel:
6 ohms (1 x 16 ohms + 1 x 8 ohms)
LOUDSPEAKER Celestion Vintage 30, 16 ohms
HEADPHONES OUT 500 mW into 4 - 600 ohms
General Specifications
MAINS VOLTAGE 230 volts AC (European version)
117 volts AC (North American version)
100 volts AC (Japanese version)
MAX. POWER CONSUMP. 708 VA
MAINS FUSE T 2.5 A (230 V model)
T 5 A (117 V model)
T 6.3 A (100 V model)
EXTERNAL FUSES T 500 mA MIDI Phantom
INTERNAL FUSES 2 x T 5 A (power amp)
1 x T 2.5 A (DSP)
2 x T 500 mA (analog section)
DIMENSIONS (W X H X D) 750 x 585 x 300 mm
WEIGHT 30 kg
r
TUNER button.
® , ensuring that it is

11.0 APPENDIX

11.1 TABLE: EFFECTS AND EFFECT PARAMETERS

The following overview gives you a survey of all of the zenTera
effects and effect parameters. Note that you must first activate the
appropriate effect menu before you can enter and edit settings.
Activate INS FX by tapping the
menus by turning or tapping
INS FX
TYPE PARA 1
Wah Wah -
Wah Wah 2 -
Fix Wah Frequency
Fix Wah 2 Frequency
Mod Wah Rate
Mod Wah 2 Rate
Comp Short Make Up Gain
Comp Medium Make Up Gain
Comp Long Make Up Gain
Tube Scream Gain
Fuzz Gain
MOD FX
TYPE PARA 1
Chorus Mono Rate
Chorus Stereo Rate
Flanger 1 Mono Rate
Flanger 1 Stereo Rate
Flanger 2 Mono Rate
Flanger 2 Stereo Rate
Phaser Rate
Phaser XL Rate
Tremolo Rate
DELAY
TYPE PARA 1
Echo Time
Ping Pong Time
Tape Echo Time
Tape Hallo Time
Tape Multi Time
Hold Echo >>PLEASE USE TAP BUTTON<<
Hold Ping Pong >>PLEASE USE TAP BUTTON<<
Hold Tape >>PLEASE USE TAP BUTTON<<
REVERB
TYPE PARA 1
Hall Time
Spring Time
Garage Time
Stage Time
Small Time
Bright Time
Normal Time
Warm Time
r
AMP TYPE knob and the remaining
Wr
MOD FX, DELAY and/or REVERB.
PARA 2
- - -
- - -
0.23 - 1.55 - -
0.50 - 2.21 - -
0.0 - 10.0 Intensity 0 - 100
0.0 - 10.0 Intensity 0 - 100
0.0 - 15.0 Intensity 0 - 100
0.0 - 15.0 Intensity 0 - 100
0.0 - 15.0 Intensity 0 - 100
0.0 - 10.0 Level 0.0 - 10.0
0.0 - 10.0 Level 0.0 - 10.0
PARA 2
0.1 - 10.0 Depth 0 - 100
0.1 - 10.0 Depth 0 - 100
0.1 - 10.0 Intensity 0 - 100
0.1 - 10.0 Intensity 0 - 100
0.0 - 10.0 Intensity 0 - 100
0.0 - 10.0 Intensity 0 - 100
0.1 - 10.0 Colour 0 - 100
0.1 - 10.0 Colour 0 - 100
0.5 - 10.0 Shape 0 - 100
PARA 2
10 ms - 2 s Feedback 0 - 100
10 ms - 2 s Feedback 0 - 100
10 ms - 2 s Feedback 0 - 100
10 ms - 2 s Feedback 0 - 100
10 ms - 2 s Feedback 0 - 100
Feedback 0 - 100
Feedback 0 - 100
Feedback 0 - 100
PARA 2
0.0 - 15.0 Predelay 0 - 100
0.0 - 15.0 Predelay 0 - 100
0.00 - 5.00 Predelay 0 - 100
0.0 - 15.0 Predelay 0 - 100
0.00 - 5.00 Predelay 0 - 100
0.0 - 15.0 Predelay 0 - 100
0.0 - 15.0 Predelay 0 - 100
0.0 - 15.0 Predelay 0 - 100
® 's
15