Pioneer VSX-D510 Operating Instructions Manual page 19

4 THE FOLLOWING FOUR SETS OF BUTTONS
ARE DEDICATED TV CONTROL. THEY ARE
ONLY USED FOR CONTROLLING YOUR TV.
TV FUNC button
Use select the TV function.
TV (POWER) button
Use to turn on the power of the TV.
TV CH +/– buttons
Use to change channels on your TV.
TV VOL +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with your
DVD player. To use first press the
then operate this button.
6 SOURCE button
Use to turn on/off the components connected to the
receiver. To use first press the
buttons then operate this button.
7 THE FOLLOWING BUTTONS ARE BOTH
CONTROLS FOR OTHER COMPONENTS (LIKE
A DVD PLAYER) AND DEDICATED TUNER
CONTROLS. THE TUNER CONTROLS ARE
EXPLAINED HERE. YOU CAN USE THEM
AFTER YOU HAVE PUSHED THE TUNER MULTI
CONTROL BUTTON.
CLASS button (see pages 25, 26)
Use to switch between the three banks (classes) of
station memories.
MPX button (see page 24)
Use to switch between auto stereo and mono
reception of FM broadcasts. If the signal is weak then
switching to MONO will improve the sound quality.
Also, this is the pause button for CDs, tapes, DVDs,
etc.
BAND button (see pages 25, 26, 29)
Use to switch between the AM and FM band when in
TUNER mode.
D. ACCESS button (see page 25)
Use to directly access a radio station by pressing the
number of the station you want.
8 LOUDNESS button
Use to switch on the loudness. This feature is useful
for getting good bass and treble sounds listening at
low volumes.
9 FUNCTION button
Use to select the playback or recording source. This
button lets you cycle through the different functions
of the receiver in the following order: CD, tuner,
CDR/TAPE/MD, VCR/DVR, DVD/LD, DVD 5.1 CH.,
and TV/SAT.
0 RECEIVER
(POWER) button
This switches between STANDBY mode and power
ON for this receiver.
button
DVD/LD
MULTI CONTROL
- FL DIMMER button
Use this button to make the fluorescent display (FL)
dimmer or brighter. There are three brightness
settings as well as an off setting.
= LED DISPLAY
This display flashes when a command is sent from
the remote control to the receiver. It also flashes at
other times, for example when teaching the receiver
preset codes with specific meanings.
~ EFFECT +/– buttons (see pages 22, 34)
Use to add or subtract the amount of effect in
different DSP sound modes or advanced listening
modes. To use first press the
operate this button.
! 2 3 (ST +/–) 5∞ (FQ +/–) & ENTER buttons
(see pages 11-15, 24, 26, 33, 34)
Use these arrow buttons when setting up your
surround sound system. These buttons are also used
to control DVD menus/options and for deck 1 of a
double cassette deck player. The
be used to find radio frequencies. The
can be used to select the stations of memorized radio
frequencies.
@ TOP MENU button
In DVD mode this button brings you to the top or
most fundamental menu.
# CHANNEL +/– buttons (DISPLAY, RF ATT)
Use to select the stations of memorized radio
frequencies. Also use to skip tracks backward or
forward on CDs, DVDs, etc. Also use to display the
information (
RDS DISPLAY
input level of a radio signal (
$ MUTING button
Use to mute the sound or restore the sound if it has
been muted.
% MASTER VOLUME +/– buttons
Use to set the overall listening volume.
^ REMOTE SETUP button (see pages 31-32)
Use this button when setting up the remote control to
control other components.
Displays & Controls
button then
RECEIVER
buttons can
FQ +/–
buttons
ST +/–
) and use to lower the
).
RF ATT
19
En