Table of Contents
Advertisement
Turning Power On or Off
Some of this unit's functions cannot be performed while the vehicle is in
motion. Be sure to stop your vehicle in a safe location and apply the
parking brake, before attempting these operations.
1
Press
SOURCE to turn on the unit.
• The unit can be turned on by pressing any button. The unit is also
automatically turned on if an iPhone/iPod or USB memory is
connected.
2
Press and hold
SOURCE for at least 3 seconds to
turn off the unit.
• The monitor may be dim during low temperature and immediately
after turning on the power. The brightness will return to normal as
time elapses.
• The iXA-W404E is a precision device. With gentle handling, its
unique capabilities can be enjoyed for a long time.
Adjusting the Volume
Rotate the Double Action encoder until the desired
sound is obtained.
• The MUTE function can be performed by using the optional remote
control.
How to view the Display
Soft button operation
• Be sure to touch the button lightly with the pad of your finger on the
display to protect the display.
• If you touch a button and there is no reaction, remove your finger
from the display, and try again.
About the button descriptions used in this Owner's Manual
• The buttons found on the face of the unit are expressed in bold
(e.g. SETUP). The buttons found on the touch-screen display are
shown in bold within brackets, [ ] (e.g. [SETUP]).
• Whenever a soft button and a head unit button have the same
function, the explanations in this Owner's Manual will describe
the function of the soft button.
Recalling the Source
Here is an example explanation for the Radio mode display on how to
recall a source.
1
Press
SOURCE to activate mode switching
screen.
2
Slide the display horizontally with your finger to
select Audio/Visual mode.
Each time you scroll the display, the mode switches
circularly in the following order:
Audio/Visual
Navigation*
3
Telephone*
Multi Info
1
*
Displayed only when NAV. IN is set to ON. Refer to "Setting the
Navigation Mode" (page 19).
2
*
Displayed only when Camera IN is set to RCA or DIRECT. Refer to
"Setting the Rear Camera Input" (page 18).
3
*
Displayed only when Bluetooth IN is set to ADAPTER. Refer to
"Setting the Bluetooth Connection (Bluetooth IN)" (page 19).
1
2
Camera*
Audio/Visual
• The mode can also be switched by pressing
• If the current mode is not Audio/Visual mode, you can switch to the
Audio/Visual mode directly by pressing
Display example for mode switching screen
Changes to the Rear Selection screen when "Setting the
Picture Output" (page 19) is set to ON.
Changes to the SETUP selection screen.
Displays the name and image of the current mode.
Displays the icons of the five modes (icon of the current
mode is highlighted).
3
Slide the display vertically with your finger, or press
SOURCE repeatedly to select RADIO source.
4
Press
/ENTER.
The Radio source is activated and the display changes to
the Radio main screen.
Display example for FM Radio main screen
Displays the source name, such as radio band, etc.,
that is selected.
Displays time, missed call
Function Guide:
The function guide display varies depending on each
source.
The contents of the function guide change by touching
2
2
[P1/2]*
, [P1/3]*
, [P1/4]*
and many other operations can be performed.
1
*
Displayed only when the optional BLUETOOTH INTERFACE
(KCE-400BT) is used.
2
*
Display may vary depending on the connected devices.
5
Repeat the procedure to select another source.
• If no operation is performed for 5 seconds, during mode switching or
Audio/Visual source selection, the screen will automatically switch to
the current mode or source.
• You can select source in the Audio/Visual mode only.
and
.
SOURCE
.
1
1
, signal strength
, ect.
*
*
2
or [
] on the function guide,
9
-EN
Advertisement
Table of Contents
