Hunter ceiling fan Instructions Manual
Hide thumbs
Also See for ceiling fan:
- Installation manual (24 pages) ,
- User manual (22 pages) ,
- Owner's manual (21 pages)
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort
and performance in your home or office for
many years. This installation and operation
manual contains complete instructions for
installing and operating your fan.
We are proud of our work and appreciate
the opportunity to supply you with the best
ceiling fan available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
What to Expect with
Your Installation
Tools Needed
30 inches
7 feet
2
Downrod
6
Light Kit
Remote Control
12
1
M0097-01 • 04/14/14 • © Hunter Fan Company
Mounting Options
Ladder
3
Wiring
Canopy
9
Operation,
Maintenance & Cleaning
14
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
4
5
Blades
10
11
Troubleshooting
?
?
?
15
17
Advertisement
Related Manuals for Hunter ceiling fan
Summary of Contents for Hunter ceiling fan
- Page 1 What to Expect with Your Installation Tools Needed Mounting Options Ceiling Bracket Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for 30 inches installing and operating your fan.
- Page 2 Assess ceiling angle Select a downrod length harmful interference to radio communications. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 3 Tools Needed www.HunterFan.com 1.888.830.1326 Pliers Wire Strippers Screwdrivers Ladder Power Drill 9/64” Drill Bit (optional) (optional) If mounting to a support structure, you will also need these tools. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 4 You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common M0097-01 • 04/14/14 • © Hunter Fan Company M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 5 To avoid possible electrical shock, before 1-888-830-1326. installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 6 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 7 4-5 full turns) until it stops. with pliers. DO NOT can be inserted. from the top of the downrod. HAND TIGHTEN. 8” 3/8” If the setscrew is not tightened securely, the fan may fall. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 8 Put the wires and downrod through the canopy. Let the canopy sit loosely on top CANOPY OR WIRES. Place the downrod of the fan. ball into the slot in the ceiling bracket. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 9 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 10 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 11 Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 12 Go to www.HunterFan.com/FAQs and click the upper switch housing. Failure to properly secure all three switch housing screws could result in the light fixture falling. “How do I install my fan without the light kit?” M0097-01 • 04/14/14 • © Hunter Fan Company...
-
Page 13: Operation Instructions
The light pull chain controls thread only the light pull chain the light fixture: on and off. through the hole in the finial and screw the finial onto the threaded rod. M0097-01 • 04/14/14 • © Hunter Fan Company... - Page 14 Your fan will turn on to indicate successful syncing. If it does not, turn off power to your fan, wait 1 minute then try again. If using the transmitter with multiple fans, repeat this process for each fan. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 15 To change the fan speed, slowly pull the fan pull-chain switch to select the desired speed. Light Operation: Press and quickly release the ON or OFF button on the remote control to turn the light OFF or ON. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 16 Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly. For questions regarding removing a light kit, call customer service 1-888-830-1326. M0097-01 • 04/14/14 • © Hunter Fan Company...
- Page 17 Transmitter only works when and click “How do I properly install held at close range multiple remote-controlled fans?” • Change battery. for information on how to correct this issue. M0097-01 • 04/14/14 • © Hunter Fan Company...