Hunter Ceiling fan Instructions Manual
Hide thumbs
Also See for Ceiling fan:
- Installation manual (24 pages) ,
- User manual (22 pages) ,
- Owner's manual (21 pages)
Table of Contents
Advertisement
Quick Links
Table of Contents
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Switch Housing
What to Expect with
Your Installation
30 inches
7 feet
2
Hanging the Fan
7
Light Kit
12
13
M3552-01 • 05/14/14 • © Hunter Fan Company
Tools Needed
Ceiling Plate
Ladder
3
Wiring
Canopy
8
Maintenance,
Operation & Cleaning
Remote Control
15
1
www.HunterFan.com
1.888.830.1326
Top Housing
4
5
Blades
9
11
Troubleshooting
?
?
?
16
18
Advertisement
Table of Contents
Related Manuals for Hunter Ceiling fan
Summary of Contents for Hunter Ceiling fan
- Page 1 What to Expect with Congratulations on purchasing Your Installation Tools Needed Ceiling Plate Top Housing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation 30 inches manual contains complete...
-
Page 2: What To Expect With Your Installation
Check box to see generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause fan weight harmful interference to radio communications. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 3: Tools Needed
Tools Needed www.HunterFan.com 1.888.830.1326 Wire Strippers Screwdrivers Ladder Power Drill 9/64” Drill Bit (optional) (optional) If mounting to a support structure, you will also need these tools. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 4: Ceiling Plate
To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the Refer to warning w.1 on pg. 2 outlet box associated with the wall switch location. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 5: Top Housing
Ensure all four screw in the top housing lineup with holes line up with the screw the holes in the motor housing. holes in both the top housing and the adapter. M3552-01 • 05/14/14 • © Hunter Fan Company... - Page 6 Install the top housing screws. Install the least 8” extending from the top of grounding screw in the smaller screw the canopy. hole. These screws can be found in the hardware bag. 8” 3/8” M3552-01 • 05/14/14 • © Hunter Fan Company...
-
Page 7: Hanging The Fan
Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. Note: Fan style may vary. M3552-01 • 05/14/14 • © Hunter Fan Company... - Page 8 Spread the wires apart, with the grounded wires on one side of the Refer to CAUTION c.1 on pg. 2 outlet box and the ungrounded wires on the other side of the outlet box. M3552-01 • 05/14/14 • © Hunter Fan Company...
- Page 9 When all the holes the holes opposite the ceiling plate hooks. are properly aligned, securely tighten all Note: The slots in the canopy must three canopy screws. remain engaged while swinging the canopy for alignment. M3552-01 • 05/14/14 • © Hunter Fan Company...
- Page 10 Note: Should you need to remove the trim ring, press firmly on opposite sides of the trim ring. The tabs will flex out releasing the canopy trim ring. M3552-01 • 05/14/14 • © Hunter Fan Company...
- Page 11 Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. M3552-01 • 05/14/14 • © Hunter Fan Company...
-
Page 12: Switch Housing
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 13: Light Kit
Make sure the light kit is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 14: Operation Instructions
Rotate the globe in a clockwise surface of the light fixture rim. direction until it is held tightly in See next page for fan place by the three tabs. operation instructions. M3552-01 • 05/14/14 • © Hunter Fan Company... -
Page 15: Remote Control
If it does not, when necessary. turn off power to your fan, wait 1 minute then try again. If using the transmitter with multiple fans, repeat this process for each fan. M3552-01 • 05/14/14 • © Hunter Fan Company... - Page 16 Insert and tighten the screws. Do not over tighten. Note: For rocker-style cover plates, break off the tabs by pushing outward. M3552-01 • 05/14/14 • © Hunter Fan Company...
- Page 17 30 seconds. After a total of 30 seconds, the lights will be completely off. Cleaning the fan - Use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. M3552-01 • 05/14/14 • © Hunter Fan Company...
-
Page 18: Troubleshooting
• Make sure the battery is installed correctly. • Check the plug connection in the switch housing. • Install a fresh battery. Transmitter only works when held at close range • Change battery. M3552-01 • 05/14/14 • © Hunter Fan Company...