Hunter ceiling fan Installation Manual
Ceiling fan
Hide thumbs
Also See for ceiling fan:
- User manual (22 pages) ,
- Owner's manual (21 pages) ,
- Manual (20 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hunter ceiling fan
Summary of Contents for Hunter ceiling fan
- Page 1 ENGLISH MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 2 Important Instructions: Keep Instructions for future use...
- Page 3 30 inches We are proud of our work and appreciate the 7 feet Ladder opportunity to supply you with the best ceiling fan available anywhere in the world. Preparation Downrod Wiring Canopy Maintenance &...
- Page 4 Check box to see accessory light kits. electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a Select a downrod length fan weight qualified electrician. c.2 - Use only Hunter replacement parts. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 5 Wire Strippers Screwdrivers 9 mm Wrench 3.5 mm Drill 8 mm Drill Bit Hammer Power Drill Bit (optional) (optional) (optional) (optional) If mounting to a support structure, you will also need these tools. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 6 The support structure must be able to support 5 Carefully choose the installation location times the weight of the fan. The weight of the fan is that allows for optimal air flow. located on the product packaging. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 7 To avoid possible electrical shock, before installing your fan, disconnect the Refer to warning w.1 on pg. 2 power by turning off the circuit breakers to the outlet box associated with the wall switch location. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 8 Note: Do not mount ceiling fan to a plastic outlet box. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 9 Save the screws. They will be next couple of steps. needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 10 Steps 1-5 to remove standard downrod pipe Longer Downrod for angled ceilings or ceilings 3 m or higher Shorter Downrod for fans installed close to ceiling Steps 6-10 to reassemble with new pipe MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 11 Hand tighten the downrod (at least 4-5 full until it rests against the hanger ball. the downrod can be inserted. turns) until it stops. Note: The adapter cover is not used for low-profile mounting. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 12 20 cm extending from the top of the DO NOT HAND TIGHTEN. flush against the motor housing. downrod. 20 cm 1 cm If the setscrew is not tightened securely, the fan may fall. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 13 Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Note: Fan style may vary. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 14 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 15 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 16 Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 17 Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 18 Make sure the globe assembly is securely attached to the shroud. Failure to properly secure all three acorn nuts could result in the light fixture falling. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 19 Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. MD511-01 • 05/20/14 • © Hunter Fan Company...
-
Page 20: Operation Instructions
The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off. MD511-01 • 05/20/14 • © Hunter Fan Company... - Page 21 To switch the direction of air flow, For cleaning the fan, use soft brushes or move the reverse switch to the cloths to prevent scratching. Cleaning opposite position. products may damage the finishes. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 22 • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 12. • Check the plug connection in the switch housing. MD511-01 • 05/20/14 • © Hunter Fan Company...
- Page 23 1. Warranty repairs shall only be performed by an Authorized Service Center appointed by Hunter Fan do Brasil, which 1. Hunter Ceiling Fans are warranted by Hunter Fan do Brasil for a period of 1 (one) year from the date of purchase by the provides specialized technicians and original parts, guaranteeing the service provided.