Operation - Haier HPU-18C03/NAF Operation Manual

Operation

Base Operation
Unit start
Press ON/OFF on the indoor unit ,or press ON/OFF
on the remote controller,unit starts.
The liquid crystal will display the working state of
last time (Except Timer and Sleep )
Select operation mode
Press DRY,COOL ,AUTO button,For each
press,operation mode changes.Press
till " " is displayed, and then press
blowing function.
Fan speed selection
Press FAN button. For each press,fan speed
changes as follows:
Remote controller:
Display
circulated
AUTO
LOW
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO,the air conditioner automatically
adjusts the fan speed according to room temperature.
Unit stop
Press ON/OFF button, the unit stops.
Air Flow Direction Adjustment
Up and down air flow
direction display
Left and right air flow
direction display
Pos.1
Pos.1
Pos.2
Pos.2
Pos.3
Pos.4
Pos.3
Pos.5
Pos.4
Pos.6
Pos.5
Pos.7
Fig.1
Pos.8
(Auto swing)
Sleep Operation
Press button to enter additional options, when
cycle display to ,
enter to sleep function.
Operation Mode
In COOL,DRY mode
1 hours after SLEEP mode starts, temp. will become 1
for further 6 hours then stops. Temp. is higher than temp.setting so that
room temperature won't be too low for your sleep.
In FAN mode
I t has no SLEEP function
Auto Operation
button,
enter to
MED
HI
Horizontal flap Vertivcal flap
Pos.1
Pos.1
Pos.2
Pos.2
Pos.3
Pos.3
Pos.4
Pos.5
Pos.4
Pos.6
Pos.5
(Auto swing)
Pos.7
Fig.3
Pos.8
Fig.2
(Auto swing)
Fig.4
will flash. And then press
Control panel display
AUTO
Fuzz
COOL Operation
COOL
COOL
DRY Operation
AUTO
Dehu
FAN Operation
LOW
Remote controller button
FAN
Up and down air flow direction adjustment
For each press of SWING button,the position of horizontal
flap and the air flow direction on remote controller display
changes as follows according to different operation models:
Remote
Pos.1 Pos.2 Pos.3 Pos.4
COOL/DRY/FAN controller
/AUTO mode
Horizontal
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5
flap
Note:When the unit is turned off by the remote controller or the control panel,the horizontal flap will close.
When the power supply is cut off directly, the horizontal flap will not close. Please use the remote controller or
the control panel to stop the unit.Do not start or stop the operation by disconnecting the power supply and so on
HEALTH Operation
Press the "HEALTH"button, "
the air condition is operating the healthy function.
Note:
When the HEALTH mode is set, the flap will keep the position you set.
It is advisable not to keep horizontal flap at downward positionfor a
long time in COOL or DRY mode,otherwise,condensate water might occur.
Left and right air flow adjustment
Move the vertical blade by a knob on air conditioner to adjust left and right direction
referring to Fig. displays as follows:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
Remote
controller
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
Vertical
flap
Temp.setting
Remote controller display
Pos.5
(Fig.3)
"is displayed,now
SLEEP operation stops
SLEEP operation starts
Rises 1
Rises 1
In COOL DRY mode
(Fig.1)
(Fig.2)
(Fig.4)
Unit stop
2