Haier HPU-18C03/NAF Operation Manual page 4

Operation
Timer On/Off On-Off Operation
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
0.5h 0.5h
TIMER ON TIMER OFF TIMER ON-OFF
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). "
3.Press / button to set time.
Press the button for each time, setting time in the
first 12 hours increased by 0.5 hour every time,
after12 hours,increased by 1 hour every time.
Press the button for each time, settiing time in the
first 12 hours decreased by 0.5 hour every time,
after 12 hours,decreased by 1 hour every time.
It can be adjusted within 24 hours.
4.Confirm timer setting
After adjust the time,press
the time ON or OFF button will not flash any more.
5.Cancel timer setting
Press the timer button by times until the time display
eliminated.
Hints:
After replacing batteries or a power failure happens,
time setting should be reset.
According to the Time setting sequence of TIMER
ON or TIMER OFF, either Start-Stop or Stop-Start
can be achieved.
Power failure resume
(please set and apply as necessary)
With setting of power failure resume, if sudden power failure
occurs,the unit will resume original operation when power is
supplied again.
Setting method: With ON of remote controller (except TIMER
and SLEEP),press button to enter additional options,
,
when cycle display to
and button in turn 10times in 7 seconds, after 4 beep from
the buzzerhe unit comes into power failure resume mode.
To cancel:
the mode cancel method is the same as setting method.The
difference is that the buzzer sounds beep twice and power failure
resume function is canceled.
Note:
1.When sudden power failure happens during unit
operaition in power failure resume mode,if the air
conditioner is not desired for use in a long period plea-
se shut off the power supply in case that the unit auto-
matically resume operation.
2.when power is re-supplied,or press ON/OFF to turn
off the unit when power resumes.
BLANK
0.5h 0.5h
TIMER OFF-ON
"or " "will flash.
button and confirm
will flash.And then press
POWER/QUIET Operation
(1)
POWER Operation
When you need rapid cooling, you can use this.
function Press button to enter additional options, when
cycle display to ,
to power function. When cancel the function, please enter
additional options again and to cancel power function.
(2) QUIET Operation
You can use this function when silence is needed for rest or
reading Press QUIET button, the remote controller will show
and then achieve to the quiet function. Press again this
QUIET button , the quiet function will be cancelled.
Note
During POWER operation, in rapid COOL mode ,
the room will show inhomogeneous temperature distribution.
Long period QUIET operation will cause effect of not too
cool .
Healthy airflow Operation
1.Press to starting
Setting the comfort work conditions.
2.The setting of healthy airflow function
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations, to choose the swing location
what you needed,and then press
Healthy
airflow
upwarder
3.The cancel of the healthy airflow function
Press button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations again,and then press
button to cancel.
Notice: Do not direct the flap by hand. Otherwise, the
grille will run incorrectly. If the grille is not run correctly, stop
for a minute and then start, adjusting by remote
controller.
Note:
1.After setting the healthy airflow function, the position
grill is fixed.
2.In cooling, it is better to select the
3.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may
occur at the grille .
will flash and then press
button to confirm.
Healthy
Present
airflow
position
downwarder
mode.
,enter
3