1. Manuals
  2. Brands
  3. Avaya Manuals
  4. Switch
  5. C460 SMON
  6. Quick start manual

Avaya C460 Quick Start Manual

Modular multilayer switch
Hide thumbs Also See for C460:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual, User Manual
Avaya™ C460
Modular Multilayer Switch

Quick Start Guide

Note:
Refer to "Important Information" before starting
the installation
IP Telephony
Contact Centers
Important Information
Unpack the Chassis
Position the Chassis
Install the Supervisor
Module and PSU
Configure the Switch
Run the Embedded Device
Manager (optional)
Unified Communications
1
2
3
4
5
6
Services

Advertisement

Table of Contents
loading

Related Manuals for Avaya C460

Summary of Contents for Avaya C460

  • Page 1: Quick Start Guide

    Avaya™ C460 Important Information Modular Multilayer Switch Quick Start Guide Unpack the Chassis Position the Chassis Install the Supervisor Note: Module and PSU Refer to “Important Information” before starting the installation Configure the Switch Run the Embedded Device Manager (optional)

  • Page 2: Notes, Cautions And Warnings

    Safety Information Warning: To avoid injury, Avaya recommends that two people lift or move the switch. A fully loaded C460 switch weighs at least 100 lbs (45 kg). Caution: The Avaya C460 switch and modules contain components sensitive to electrostatic discharge.

  • Page 3: Power Supplies

    Warranty: Avaya Inc. provides a limited warranty on this product. Refer to your sales agreement or other applicable documentation to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language as well as information regarding support for this product, while under warranty, is available through the following website: support.avaya.com.

  • Page 4: Unpack The Switch

    Equipment • One C460 chassis with fan module. • If you purchased an Avaya C460ML-CFG (Material code 700255003) or C460ML PWR CONFIG (Material code 700281603) , then one Supervisor Module, PSU and the Fan Module are already installed. Ethernet connection cables are not supplied.

  • Page 5: Position The Switch

    C460 switch weighs at least 100 lbs (45 kg). You can position the Avaya C460 in free-standing mode on a suitable shelf or table, or mount it in a standard 19-inch equipment rack in a wiring closet or equipment room.

  • Page 6: Installing The C460 On A Table Top

    Figure 4 Table-Top Installation Rubber feet Ensure that all the preinstalled components are firmly installed in the chassis. These include: — Supervisor modules — Power supply — Fan module Caution: Do not place other equipment on top of the C460.

  • Page 7: Rack Mounting (Optional)

    Warning: To avoid injury, Avaya recommends that two people lift or move the switch. A fully loaded C460 switch weighs at least 100 lbs (45 kg). You can mount the Avaya C460 in a standard 19" rack either in “front-mount” or “mid-mount” positions with the brackets supplied with the chassis.
  • Page 8 Firmly fix the brackets to the chassis with the screws provided. Use five screws for each bracket. Position the switch in the rack. Fasten the switch in the rack with the screws provided. The screw size is 8-32x¼ Caution: Do not place other equipment on top of the C460...

  • Page 9: Cable Guide Installation

    You can use the cable guide to tidy cables from the Supervisor and I/O modules. The cable guide is symmetric: you can install the bracket on either side of the switch. Avaya recommends that you install the cable guide on the left side of the switch to allow easier access to the fan module.

  • Page 10: Install The Supervisor Module And Psu

    If you purchased an Avaya C460ML-CFG (Material code 700255003, PEC Code 4548-009), then one Supervisor Module, PSU and the Fan Module are already installed. Figure 8 shows the positions of the SPV Supervisor installed in the C460 chassis. Figure 8 Location of the Avaya C460 Supervisor Modules You can install Supervisor modules in the top two slots –...
  • Page 11 Position the module in the slot. See Figure 9. Gently slide the module in. Close the locking handles. Gently tighten the screws. For information on configuring redundant supervisor modules, refer to “M460ML-SPV Supervisor Module Redundancy“ in the Avaya C460 Installation and Maintenance Guide.

  • Page 12: Installing A Psu

    Refer to the Avaya C460 Installation and Maintenance Guide for further information. The C460 is now ready for operation with its default settings (see Table 12, “Default System Parameters”). If you wish to configure the switch, see “Configure the Switch”.

  • Page 13: Configure The Switch

    Configure the Switch Before you can set up the C460 you must install at least one supervisor module and PSU and then turn on the switch. You can configure the switch via sideband, inband or outband interfaces. Connecting the Serial Console Port Each Avaya C460 supervisor module has one serial port on the front panel for connecting a terminal, a terminal emulator, or a modem.
  • Page 14 Figure 10 M460ML-SPV Supervisor Module Serial Console Port Perform the following steps to connect a terminal to the C460 Serial Console port for configuration of switch parameters: Use the serial cable supplied to attach the RJ-45 RS-232 console connector to the Console port of the active M460ML-SPV module.
  • Page 15 Verify that you can communicate with the C460. Use the ping command to the inband interface IP of the C460. If there is no response using the Ping command, check the IP address and default gateway of both the C460 and the station.
  • Page 16 — Start the Telnet session by typing: telnet <C460_IP_address> For example: telnet 149.49.35.214 The Login Name prompt is displayed Enter the default name root The password prompt is displayed Enter the password in lower case letters. root You can now configure the C460.

  • Page 17: Avaya C460 Default Settings

    Avaya C460 Default Settings We recommend that you use the CLI to change default parameters. Refer to the Avaya C460 documentation for more information. Table 12 Default System Parameters Parameter Default Value All IP addresses N/A (0.0.0.0) CLI timeout 15 minutes...

  • Page 18: Run The Avaya C460 Embedded Device Manager (Optional)

    The user name is “root” The default passwords for read-write access is “root”. The C460 Manager passwords are the same as those of the CLI. If you change the passwords of the CLI then those passwords become active for Web management as well.
  • Page 19 If you have the Java plug-in installed, the C460 Manager opens in a new window. See Figure 14 Figure 14 C460 Device Manager If you do not have the Java plug-in installed, follow the instructions on the Welcome page that offers a variety of options to install the plug-in.

  • Page 20: Avaya Support

    Avaya Web site: http://www.avaya.com © 2003 Avaya Inc. All rights reserved. All trademarks identified by the ® or TM are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners Catalog No DO0755 Rev.

Table of Contents