Vtr 2 Menu; Vtr 3 Menu - JVC GY-HD100E Service Manual

1.5.7 VTR 2 menu

In a service menu, place the cursor on "VTR 2" and push the
SHUTTER dial to display the VTR 2 menu.
– – – V T R 2
L O N G P A U S E
B A T T . S H U T D OWN
B A T Y . A L A RM
A N T O N S H U T D OWN
A N T O N A L A RM
D F M A S K [ D V ]
P A G E B A C K
Fig. 1-5-7
Operation ways are almost same as CAMERA 1 MENU, so
please refer it.
Item
LONG PAUSE OFF Disable the long pause function.
ON Enable the long pause function.
6.8V Setting of the battery voltage when
BATT.
shutdown should occur. (Setting in
SHUTDOWN *1
0.1V steps between 6.3V and 7.5V.)
6.9V Setting of the battery voltage when
BATT.
battery alarm is indicated. (Setting in
ALARM *1
0.1 V steps between 6.3V and 8.0V.)
ANTON SHUT 12.0V Setting of the ANTON battery voltage
when shutdown should occur. (Setting
DOWN
in 0.1V steps between 10.5V and
13.6V.)
ANTON 13.5V Setting of the ANTON battery voltage
when battery alarm is indicated.
ALARM
(Setting in 0.1 V steps between 10.5V
and 13.6V.)
OFF "1" is recorded as per format.
DV DF MASK *2
ON "0" is always recorded.
Table 1-5-7
*1 : When operating by DC input, then "SHUT DOWN" will be
set to 6.0V, and "ALARM" will be set to 6.9V automati-
cally, and these setting will not relate to menu setting.
*2 : FRAME RATE 50/25 only
1-12
– – –
O N
6 . 0 V
6 . 9 V
1 2 . 6 V
1 3 . 5 V
O F F
Parameter
( indicates the factory setting.)

1.5.8 VTR 3 menu

In a service menu, place the cursor on "VTR 3" and push the
SHUTTER dial to display the VTR 3 menu.
– – – V T R 3
R E S E R V D
B A T T E L Y I N F O . .
P A G B A C K
Fig. 1-5-8 (1)
Changing of setting is prohibited.
Item
RESERVED 0 Normal setting
BATTERY INFO
Refer to next page.
Table 1-5-8 (1)
BATTERY INFO Display
Display method
Move the cursor to the "BATTERY INFO.." in "VTR3" screen
and press SHUTTER dial. BATTERY INFO screen (right fig-
ure) will be displayed.
– – – B A T T E R Y
T Y P E
R E M A I N
< 1 2 . 8 V 1 . 2 5 A 3 0 ° C >
F U L L C A P A C I T Y
P R E S E N T C A P A C I T Y 3 0 . 5 A h
S E R I A L N O .
M A N U F A C T U R E
S O F T W A R E R E V .
C A L I B R A T I O N R E Q U I R E D O F F
P A G E B A C K
Fig.1-5-8 (2) BATTERY INFO
(When the Anton/Bauer Smart Battery is detected)
– – –
0
Parameter
( indicates the factory setting.)
I N F O – – –
A N T O N S M A R T
1 2 5 M i n / 9 5 %
3 2 . 6 A h
5 5 5 2 0
2 0 0 4 / 0 4
1 2 . 5