( Wps Settings); Cannot Connect. Multiple Access Points Are Enabled. Is Displayed; Connection Failed. Is Displayed; Problems During Software Installation - Canon Pixma MP560 Series Getting Started

Problems during Software Installation
( WPS Settings) The Machine is Not Displayed (Detected)
A
!f,,..,
l"C~I",to
0..
~.1Od <.o<>ld """
""d.I«I.d,
.~llh. n.tooo<~ •• 11'''111 wf.... ci<,:k'~Iil(V~I.l
Nt., y.... l~,r. _1ft.
:><i!'lU' " ........
l£•• ~ _
",,""'.., ...
m,•• ~ ..,.",., u" bf. d<!U.IM. W<>i{ ~""';Io a~<l ",."
.1..kWpd.,.j.
M
A
Is the machine connected to a network?
For details on how to check if the machine is connected to a network, refer to "Confirm Connection
Status" on page 27 in the printed manual: Getting Started.
;ii'-"
~;
$ '
If the machine is not connected to a network, perform setup again by following the
procedures in "Wireless Setup" on page 19 and onward in the printed manual: Getting
Started.
Set the access point to accept the IP address of the machine.
For details on how to change the settings of the access point, refer to the manual supplied with the
access point or contact its manufacturer.
• To check the IP address of the machine, press the HOME button, then using the Easy-Scroll
Wheel and OK button. select Settings> Device settings> LAN settings> Confirm LAN
settings> Wireless LAN setting list, then check IP address.
~~~~~~~~~;~~:-.~~:~~-~
1
r-,;;"~-::;;I""f';;.,-;::.;;;; ~
,I
I
-..J
I
·h_"l'<-'-'-"_~<:«l-.c ~"'_
.:'".,....::;;:;- ....
·_""'~e-
...
9_. . . _ .""_'_
__"_J -
----,=,~_',,,J
EmIlI
Make sure that you follow "Connection Checklist" on page 11. then click Update (A).
...
Is the IP filtering feature enabled on the access point?
• For details on how to check the settings of the access point, refer to the manual supplied with the
access point or contact its manufacturer.
___ C - h - e - c k - - - - - - - - - - -....
"LIW:.i: ••
~M
Connection failed. is Displayed
Cannot connect. Multiple access points are enabled. is Displayed
Action
,.,"',.,
M
.'&.lal,
.1'.' ......
.....
The message appears when multiple access points are
-~
"
detected.
,
ErrOl"
,,~j':;f
Wait for a while, then configure the settings again.
Cannot connect
II
Mu~iple access points are
~
enabled,
.~
~
"m
".',.-
Check
nAn
M
"·&'jl • • •
1','...... \ "
....
The message appears when an error occurs.
:~i-""r: '~":!
'&rOt;' ,
,I
Check the access point settings. then configure WPS
'Iie,'if.:
t,
settings again.
Connection failed.
For details on how to check the settings of the access point,
See the manual,
i
refer to the manual supplied with the access point or contact its
I
manufacturer.
I
For the procedure to configure WPS settings of the machine, refer
j-m--
"
-
--
- - -
.
to "Wireless Setup Using WPS (Wi-Fi Protected Setup)" on page
24 in the printed manual: Getting Started.
.
When using an access point that does not support WPS. configure settings manually. For the
procedure to configure settings of the machine manually, refer to "Wireless Setup" on page 19 in
the printed manual: Getting Started.
>
.,.,
4