Safety Information - Slant/Fin VICTORY VSPH SERIES User's Information Manual

V
ICTORY VSPH Models
ANNUAL SERVICE AND GENERAL MAINTENANCE
A trained and qualified service technician should per-
form inspection and general maintenance listed in
Installation and Operating Instructions (Publication No.
VSPH-40) before each heating season and at regular
intervals.
SAFETY AND OPERATING INSTRUCTIONS
Follow the lighting instructions in this manual. These
instructions are also attached to the boiler.
WARNING: If you do not follow these instructions exactly, a
fire or explosion may result causing property damage, per-
sonal injury or loss of life.

SAFETY INFORMATION

For Your Safety Read Before Operating
A. This appliance is equipped with an ignition device
which automatically lights the pilot. DO NOT try to light
the pilot by hand.
B. BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light any appliance.
• DO NOT touch any electric switch: DO NOT use any
phone in your building.
• Immediately call you gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to turn the gas control knob. Never
use tools. If the knob will not turn by hand, don't try to
repair it, call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. This appliance is equipped with an ignition device
which automatically lights the pilot. DO NOT try to light
the pilot by hand.
5. Remove jacket front panel
6. Turn gas control knob clockwise
DO NOT force.
7. Wait five (5) minutes (longer for propane) to clear out
any gas, then smell for gas, including near the floor. If
you then smell gas, STOP! Follow "B" in the safety infor
mation above on this page. If you don't smell gas, go to
next step.
8. Turn as control knob counterclockwise
9. Replace jacket front panel.
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the instructions
"To Turn Off Gas to Appliance" and call your service
technician or gas supplier.
1. Set thermostat to lowest setting.
2. Turn off all electric power to the appliance if service
is to be performed.
3. Remove jacket front panel.
4. Turn gas control knob clockwise
stops, then continue to "OFF". Do not force.
5. Replace jacket front panel.
GAS GAS
I NLE T I NLE T
Figure 7.
Removing Jacket Front Panel
1. Turn black screws
2. Remove front panel.
To replace the panel, reverse procedure.
INTEGRATED BOILER CONTROL
The integrated boiler control monitors the status of the
room thermostat, high limit control (Aquastat), pressure
switch (air flow proving switch) and the flame sensor. It
controls the operation of the circulator, inducer motor
(blower), gas valve and spark for pilot ignition. The boiler
control also determines the sequence of operation and
timing for pre and post purge periods, trial for ignition adn
lockout. The control indicator lights (LED's) provide infor-
to "OFF".
mation of boiler operation when lights are steady on or
diagnostic information when they are flashing in order to
help to determine the cause of boiler failure.
To Turn Off Gas to Appliance
Gas Valve VR8204 or VR8304
HON EYWELL HON EYWELL
ON ON
0FF 0FF
GAS CON TROL KNO B GAS CON TROL KNO B
SHOW N I N " OFF " SHOW N I N " OFF "
POSITI ON POSITI ON
FI GURE 19 FI GURE 19
VSP40-19 VSP40-19
1 ⁄ turn to open position.
4
6
to "ON".
till knob
OUTLE T OUTLE T