Sharp AR-M160 Service Manual page 35

Main Sub
Contents
code code
24 07 Drum counter clear
08 Copy counter clear
09 Printer counter clear
13 Scanner counter clear
14 SPF jam total counter clear
15 Scanner mode counter clear
25 01 Main motor operation check
(Cooling fan motor rotation check)
10 Polygon motor operation check
26 02 Size setting
03 Auditor setting
04 Copier duplex setting
When the [START] key is pressed, the drum count and the drum roasting time are reset to zero, and
the drum counter value is displayed on the 7-seg LED. When the [Interrupt] key is pressed, the
machine goes into the sub code input standby mode. When the [CA] key is pressed, the simulation is
terminated.
When the [START] key is pressed, the copy count value is reset to zero and displayed on the 7-seg
display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the printer count value is reset to zero and displayed on the 7-seg
display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the scanner count value is reset to zero and displayed on the 7-
seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the SPF jam total count value is reset to zero and displayed on the
7-seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input standby
mode. When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the scanner mode count value is reset to zero and displayed on
the 7-seg display. When the [Interrupt] key is pressed, the machine goes into the sub code input
standby mode. When the [CA] key is pressed, the simulation is terminated.
When the [START] key is pressed, the main motor (together with the duplex motor for the duplex
model) is driven for 30 sec. At that time, to save toner consumption, if the developing until is installed,
the developing bias, the main charger, and the grid are outputted. Since, in that case, laser discharge
is required when the motor stops, the polygon motor is driven simultaneously. Check if the
developing unit is installed or not. If it is not installed, the above high voltage is not outputted and only
the motor is rotated. After completion of 30 sec operation, the machine goes into the sub code input
standby mode.
* This simulation must not be executed by forcibly turning on the door open/close switch.
When the [START] key is pressed, the polygon motor is rotated for 30 sec. After completion of 30 sec
operation, the machine goes into the sub code input standby mode.
Used to set Enable/Disable of the FC (8.5" x 13") size detection.
Code number
0 FC detection Disable
1 FC detection Enable
Detection size when a document of the FC ((8.5" x 13") size is used
Unit to
Destination
be used
Document SPF EX Japan AB
series (FC)
Inch series (FC)
•For the other destinations, this setting is disabled.
Used to set the auditor.
Code number
0
1
2
* When the coin vendor mode is selected, if the auditor setup is ON and the standard tray is
manual feed tray, the standard tray setup must be changed to the main cassette.
When this simulation is executed, the current set duplex code number is displayed. Enter the desired
code number of duplex setting and press the [START] key, and the entered code number is set.
Code number
0
1
* When this simulation is executed, the binding margin setup is automatically set to the default
(left side).
AR-M205 SIMULATIONS 7-8
Details of operation
Setting
* Default except for the following
* Default only for SCA/Philippines
Document size
FC (8.5" x 13") B4
B4 B4
FC (8.5" x 13") LG (8.5" x 14")
LG (8.5" x 14") LG (8.5" x 14")
Mode
Built-in auditor mode
Coin vendor mode
Other
Mode
Without duplex
With duplex
Setting
0 (Disable) 1 (Enable)
FC (8.5" x 13")
FC (8.5" x 13")
FC (8.5" x 13")
FC (8.5" x 13")