Installer System Test - Honeywell T7200D Product Data

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES
Installer Setup
Number
(Press Unoccupied
Select Temp to change)
Temperature 37
display adjustment.
Minimum off-time 38
in heating.
Not used. 39
Installer Setup 40
lockout (enable/
disable keypad
lockout using DIP
switch 1 on
thermostat back).
a
Number 2 must be set to 1 to extend fan operation.
b
Number 22 must be set to 1 and remote sensor(s) must be installed.
IMPORTANT
Review the settings to confirm that they match the
system. Press Run Program to exit the Installer
Setup. The thermostat has saved the Installer Setup
changes and initiated reset in order to operate with
these new settings. Be sure to set the current day
and time immediately.
Setting Current Time/Day
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended power
loss, 1:00 pm flashes on the display until a key
is pressed.
Set Current
Set Program Set Temperature
Day/Time
Run Occupied Unoccupied Occupied
Program Start Time Start Time Day Temp
Temporary Set Current Clear
Occupied Day/Time Start Time Copy
Continous
Unoccupied System
2. Press Day until the current day is displayed.
NOTE: Sun = Sunday, Mon = Monday, Tue = Tuesday,
Wed = Wednesday, Thu = Thursday,
Fri = Friday, Sat = Saturday.
Day
Set Program Set Temperature
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System Fan
3. Press increase or decrease
time is displayed.
Table 7. Thermostat Installer Setup Options. (Continued)
Factory Setting
Display
0 No difference in displayed
temperature and actual room
temperature.
4 4: 4-minute minimum off-time
— —
0 0: No Installer Setup lockout.
Set Day/Time
PM
Change
Time/Temp
Unoccupied
Temp Mon
Heat/Cool
Settings
Fan
M4951B
Set Day/Time
PM
Change
Time/Temp
Tue
M4952B
key until the current
Description Display
1 - 6
0, 1, 2,
3, or 5
—
1
NOTE: Tapping Set Current Day/Time changes the
time in one hour increments.
4. Press Run Program.
Run
Program

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat
configurations and operation. Refer to Table 8 for a list of
available system tests. To start the system test:
CAUTION
Possible Equipment Damage.
Equipment damage can result if compressor is
cycled too quickly.
The minimum off time for compressors is bypassed
during the Installer System Test. Equipment damage
can occur if the compressor is cycled too quickly.
Press and hold both the increase
until 10 appears. All segments of the LCD display for three
seconds before 10 appears. See Fig. 15 and 16.
13
Other Choices
(Press or to change)
Description
1: Display adjusts to 1°F (0.6°C) higher
than actual room temperature.
2: Display adjusts to 2°F (1.1°C) higher
than actual room temperature.
3: Display adjusts to 3°F (1.7°C) higher
than actual room temperature.
4: Display adjusts to 1°F (0.6°C) lower than
actual room temperature.
5: Display adjusts to 2°F (1.1°C) lower than
actual room temperature.
6: Display adjusts to 3°F (1.7°C) lower than
actual room temperature.
Minimum number of minutes (0 through 5)
the heating equipment is off between calls
for heat.
—
1: Installer Setup lockout activated.
Set Day/Time
PM
Set Program Set Temperature Change
Time/Temp
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Tue
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System Fan
AM
Set Program Set Temperature Change
Time/Temp
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp Mon
Occupied 1
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
System
Continous
Unoccupied System Fan
Heat
and decrease
Actual
Setting
—
M4953B
Room
Fan
Auto
M4954A
keys
63-4355—4