Zenith projection tv r49w36, r56w36 operating guide (60 pages)
Summary of Contents for Zenith D52WLCD Series
Page 1
SERVICE MANUAL Model Series: Product Type: Rear Projection LCD D52WLCD Chassis: 094A D52WLCD4 Manual Part #: 923-03485R1 Manual Series: PV154 Model Line: Product Year: 2002 REVISED EDITION First revison - Training material added CONTENTS General Info ..........1 Service Menu ..........2 Servicing .............
When servicing this product, under no circumstances should the original design be modified or altered without permission from Zenith Electronics Avoid conditions of high humidity such as: outdoor patio installations Corporation. All components should be replaced only with types identical to...
Green (flashing) The lamp cover is not closed. Orange The projection TV is overheating. Temperature Indicator The projection TV shut down due to overheating. Red (flashing) The projection TV shut down, check the cooling fan. D52WLCD OVERVIEW...
Page 7
PIP Display MONO This display appears when PIP is active. Ch.6 AM 03:00 Time Mute Appears when Appears pressing the when sound enter button on Volume is muted. remote control. Volume level is displayed while adjusting the sound. D52WLCD OVERVIEW...
Page 8
OVERVIEW Front Panel Controls Power On / Off Menu Enter (Same as ENTER button on your remote control) VOLUME UP / DOWN CHANNEL UP / DOWN Operation indicator. Lamp indicator. Temperature indicator. power menu enter D52WLCD OVERVIEW...
Scrolls the Surf channel information banner is displayed. list. exit Not functional EXIT Clears all on-screen dis- plays and returns to TV skip record stop viewing from any menu. pause rew play D52WLCD OVERVIEW...
SKIP record stop skip Functions as a song selec- RECORD, PAUSE, REW, tor in audio mode and a FFWD, PLAY, STOP pause rew play movie chapter selector in Control the functions on your VCR. aux/DVD mode. D52WLCD OVERVIEW...
Blue Reflection 1st Illumination Lens PBS Array 2nd Fly-eye LCD (Green) Lens Dichroic Green Lens Blue 1st Fly-eye (DGL 60) C-Lens 1 Lens Mirror 4 Blue Reflection Lamp Mirror 1 Mirror 3 Dichroic Red Reflection Dichroic Blue Transmission D52WLCD OVERVIEW...
Page 16
Dichroic mirrors are used to separate the light into red, green, and blue. A Dichroic mirror allows a certain wavelength of light to pass through while refecting another. Dichroic Red Reflection: Reflects red light and allows all other colors to pass through. Dichroic Blue Transmission: Allows blue light to pass through and reflects others. D52WLCD OVERVIEW...
Page 17
Black Stripe layer. Black Stripe: Improves contrast by blocking outside light. Diffusion Plate: Improves viewing angle by diffusing the light. Hard Coat: Protects the screen surface and helps improve contrast. Hard Coat Anti-Static ENTICULAR RESNEL CREEN D52WLCD OVERVIEW...
LCD can display the video (especially with video games). The response time of new LCDs isn't a factor for most uses, but older models can display noticeable ghosting due to slower response times. D52WLCD OVERVIEW...
The desired inputs can be independently assigned to each output (in the audio system, the left and right channels are processed as one unit) by I 2 C bus control. However, the same input is assigned to both the video and audio system output 3. D52WLCD CIRCUITS...
Page 22
Y = 0.3R + 0.59G + 0.11B Cb = 0.564 (–0.3R – 0.59G + 0.89B) The SYNC counter block counts the frequency of the input H Cr = 0.713 (0.7R – 0.59G – 0.11B) and V sync signals. D52WLCD CIRCUITS...
Page 23
Green so that the clamp pulse does not overlap the video interval to prevent clamping error. Count value ([DEC] $ [HEX]) = fH # 5ms V sync signal fV [kHz] Count value [HEX] Count value ([DEC] $ [HEX]) = 1/(fV # 32ns) D52WLCD CIRCUITS...
Page 25
The high-pass filters formed by the coupling capacitors at pins ANA_IN1+ and ANA_IN2+. 2) Demodulator: Standards and Features The MSP 3440G is able to demodulate all TV-sound stan- dards worldwide including the digital NICAM system. D52WLCD CIRCUITS...
Page 26
CIRCUIT DESCRIPTIONS (3) Block Diagram Fig Signal flow block diagram of the MSP 3440G(input and output names correspond to pin names) D52WLCD CIRCUITS...
Using the customer’s remote control, press and hold the menu button. When the OSD menu disappears, press numbers 9, 8, 7, 6 and press the OK button to enter the ADJ mode. The display will show “Lamp Life Time XX Hrs”. D52WLCD DISASSEMBLY...
5. Once the screws are removed, carefully pull the screen a short distance away from the cabinet. 6. Remove the speaker and connections. 7. Now the screen can be removed. D52WLCD DISASSEMBLY...
Page 36
12. Remove the metal support bracket that is mounted around the lens. 13. Remove the screws along the sides and across the top. 14. Lift up and back slightly to remove the cover to gain access to electrical components of the TV. D52WLCD DISASSEMBLY...
6. Remove the bottom of the cage and that will provide access to the Optics Engine. 7. Before removing the optics engine, use hot glue below the control knobs to lock them in place. This will help prevent the keystone and tilt settings from changing. D52WLCD DISASSEMBLY...
(Input a R, G, B input signal, then adjust it individually) 6) When finishing the adjustment, exit adjustment mode by pressing IN-START button on SVC remote control. 1) Adjust Mode : Sub adjustment menu selected by IN- START key. RGB alignment is selected in this case. D52WLCD ADJUSTMENTS...
1) Connect a power source with TV Set and turn TV Set on. by pressing IN-START button on SVC Remote Control. 2) Do heat run for 5 min and over before adjustment. 3) Receive the main/sub signal of company through 13CH by split screen. D52WLCD ADJUSTMENTS...
Page 40
2) Press 5. AD9883 adjust to adjust . 3.7050 RGB Set. 3) When the AD9883 Gain Adjust has appeared after AD9883 6) Check the data 1.RContrast, 8.GContrast, 15.BContrast is Offset Adjust, the adjustment is completed. 515. Otherwise set the data 515 by using volume button. D52WLCD ADJUSTMENTS...
Page 41
H Coefficient(KHH, KHL) If it’s not, press the IN-START button on SVC Remote --> Calculation method (CEHP-CSHP=1280, Horizontal Control and then adjust the level data of each step manu- segment value =16) ally in sub menu of No. 8.Gamma Data. D52WLCD ADJUSTMENTS...
Page 42
L1coeff(hex) = hex(0.00390625 x 2 ) = 0 x 0400 Middle level when 3coefficient --> L1H(high 9bit) = b’000000010 L1L(low 9bit) = b’000000000 35. GLMID1 : Setting up the MIDDLE 1st Level of G --- Max level when 3coefficient D52WLCD ADJUSTMENTS...
Page 43
Adjust screen coordinates data to adjust the color unifor- mity of miner point. At this time, make sure that deviation is +5~-5% and stan- dard is color coordinate of center. 5) White the miner, middle, maximum data for each point to confront to each MICOM address. D52WLCD ADJUSTMENTS...
Schematics Main Circuit ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 53 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Digital Circuit CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 54 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Microprocessor Circuit ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 55 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Digital Microprocessor Circuit CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 56 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Decoder Circuit ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 57 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Driver Circuit CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 58 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
LCD Driver Circuit - Green ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 59 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
LCD Driver Circuit - Red CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 60 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
LCD Driver Circuit - Blue ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 61 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
I/O Switch Circuit CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 62 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Keyboard & LED Circuit ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 63 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Power Supply Circuit CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 64 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Tuner Circuit 1/2 ALL SYMBOLS WITH “M” ON END OF DESIGNATOR CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR D52WLCD - 923-03??6 SHEET 65 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...
Tuner Circuit 2/2 CRITICAL SAFETY COMPONENTS ARE IDENTIFIED BY THE LETTER “X“ IN THEIR ALL SYMBOLS WITH “M” ON END OF DESIGNATOR D52WLCD - 923-03??6 SHEET 66 COMPONENT DESIGNATORS. REPLACE ONLY WITH PART NUMBERS SPECIFIED. INDICATE SURFACE MOUNTED COMPONENT...