Pioneer DJM-600 Service Manual page 71

1 Main Microphone Input Terminal and Microphone
Control Knob
Main Microphone Input Terminal:
For connecting a microphone that has a cannon-type
terminal.
MIC LEVEL (microphone level):
Adjusts the volume of the main microphone.
(Attenuation: – to 0dB)
HI:
Adjusts high-tone microphone sound.
At the center position, sound is flat.
Turn to the right to increase sound (to +12dB at 10kHz).
Turn to the left to decrease sound (to –12dB at 10kHz).
MID:
Adjusts mid-tone microphone sound.
At the center position, sound is flat.
Turn to the right to increase sound (to +12dB at 1kHz).
Turn to the left to decrease sound (to –12dB at 1kHz).
LOW:
Adjusts low-tone microphone sound.
At the center position, sound is flat.
Turn to the right to increase sound (to +12dB at 100Hz).
Turn to the left to decrease sound (to –12dB at 100Hz).
2 Input Selector Switches, Control Knobs, and Peak
Level Meters for CH-1 to CH-4
Input Selector Switches:
These switches select what input source to use from
among the units connected to each channel.
CH-1: Switches between CD1/LINE and LINE
CH-2: Switches between CD2/LINE and PHONO 1
CH-3: Switches between LINE and PHONO 2
CH-4: Switches between LINE and SUB MIC/PHONO 3
TRIM:
Adjusts the input signal level.
Turn to the right to increase level (to +9dB).
Turn to the left to decrease level (to – ).
HI:
Adjusts high-tone input sounds.
At the center position, sound will be flat.
Turn to the right to increase sound (to +12dB at 13kHz).
Turn to the left to decrease sound (to –26dB at 13kHz).
MID:
Adjusts mid-tone input sound.
At the center position, sound will be flat.
Turn to the right to increase sound (to +12dB at 1kHz).
Turn to the left to decrease sound (to –26dB at 1kHz).
LOW:
Adjusts low-tone input sound.
At the center position, sound is flat.
Turn to the right to increase sound (to +12dB at 70Hz).
Turn to the left to decrease sound (to –12dB at 70Hz).
Peak Level Meter:
Displays peak level, held for 2 seconds.
Displays level before it is subjected to the channel fader.
Display range: –24dB to +14dB.
3 MONO/STEREO (Master Output Monaural/Stereo
Selection Switch)
Used to select either MONO or STEREO for master output.
4 POWER (Power Supply Switch)
5 MASTER LEVEL (Master Level Meter)
Displays the output level following master volume
adjustment, held for 2 seconds.
Display range: –24dB to +14dB.
6 TALK OVER
While this switch is held down, sound levels other than
the main microphone's will be lowered to around 14dB.
7 HEADPHONES CUE and AUTO BPM COUNTER
SELECTOR
HEADPHONES CUE:
Used to select the source (CH-1 to CH-4, MASTER, or
E F F E C T S / S A M P L E R ) t o b e m o n i t o r e d w i t h
headphones. Press it again to cancel the selection.
Pressing multiple buttons makes it possible to derive
mixed sound from the selected sources.
AUTO BPM COUNTER SELECTOR:
When AUTO BPM has been selected with the effect/
sampler selector switch (^), the BPM of the selected
channel (CH-1 to CH-4) will be displayed on the BPM
display ($).
BPM will not be displayed correctly if 2 or more channels
have been selected.
DJM-600
71